background image

 

 
 
 

13 

Operation Cautions: 

 

 

Read and understand all instructions and warnings in this manual before operating the appliance.   

 

 

Always leave safety grills and filters in place. Without these components, operating blowers could catch 
on to hair, fingers and loose clothing. 

 

 

NEVER dispose cigarette ashes, ignitable substances, or any foreign objects into blowers. 

 

 

NEVER leave cooking unattended. When frying, oil in the pan can easily overheat and catch fire. The 

risk of self-combustion is higher when the oil has been used several times. 

 

 

NEVER cook on “open” flames under the range hood. Check deep-fryers during use: Superheated oil 
may be flammable.

 

 
 

10. TROUBLESHOOTING                                                                          

 

 

 

 

 

 

 

 

 

 
 

If the range hood or LED 
light does not operate after 
installation

 

 

Check if the range hood has been plugged in, make sure that all power has 

been turned back ON, fused not blown and all electrical wiring are 

properly connected. 

 

 

Swap out light assembly to working ones to deter-mine whether it is 

caused by defective bulbs. See 

Replacing the Light Bulbs 

on Page 

14

The range hood vibrates 
when the blower is on

 

 

The range hood might not have been secured properly on to the cabinet or 

wall.

 

The blower or fan seems 
weak

 

 

Check that the duct sized used is at least  8”. Range hood WILL NOT 

function efficiently with insufficient duct size. 

 

 

Check if duct is clogged or if air damper unit (half-circular flapper) is not 

installed correctly or opening properly. A tight mesh on a side wall cap 

unit might also cause restriction to the air flow. 

The lights work but the 
blower is not spinning at 
all, is stuck or is rattling

 

 

The blower might be jammed or scraping the bottom due to shipping 

damage.   

 

Disconnect the power cord, open the Blower unit case, rotate  the fan 

blade, might see the fan blade or/and motor is not in the proper position 

(offset from the center). Try to fix/adjust  it or please contact us 

immediately.

 

The hood is not venting out 
properly

 

 

Make sure the distance between the stove top and the bottom of the hood is 
within  recommended  24” and 27” in distance. *

Due to different ceiling 

height configurations, recommended height may not be applicable.

 

 

 

Reduce the number of elbows and length of duct work. Check if all joints 

are properly connected, sealed, and taped. 

 

 

Make sure the power is on high speed for heavy cooking. 

Summary of Contents for RH-SP08


















Reviews: