background image

PLEASE READ THESE IMPORTANT SAFETY RULES

3

PLEASE READ THIS INSTRUCTION MANUAL BEFORE ATTEMPTING TO INSTALL

OR USE THE OPENER. FAILURE TO COMPLY WITH THE INSTALLATION 

INSTRUCTIONS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.

For 

SAFETY

protection a Photo Electric Beam 

MUST

be fitted with this opener. Failure to comply 

will

void

the warranty and may result in serious personal injury
and/or property damage

DO NOT

operate the opener unless the door is in full

view and free from objects such as cars and 
children/people. Make sure that the door has finished
moving before entering or leaving the driveway.

DO NOT

operate the opener when

children/persons are near the door. Children must be
supervised near the door at all times when the 
opener is in use. 

SERIOUS PERSONAL INJURY

and/or property damage can result from failure to follow
this warning.

DO NOT

allow children to operate the opener. 

SERIOUS PERSONAL

INJURY

AND/OR 

PROPERTY DAMAGE

can result from failure to 

follow this warning.

Make sure that the 

SAFETY OBSTRUCTION

DETECTION 

system is working correctly, and is

TESTED

every month. Test as per the Installation

Instructions Manual. Adjust if necessary and recheck.
Failure to follow this rule could result in 

SERIOUS

PERSONAL INJURY

and/or property damage. This

test must be repeated at regular intervals and the
necessary adjustments made as required.

If using a key switch or keypad or any device that can
operate the opener, make sure it is out of reach of 
children and that the doorway is in full view at all times.

Make sure that remote controls are kept out of reach of 
children.

Warning - It is vital for the safety of persons to follow all instructions. Failure to comply

with the following Safety Rules may result in serious personal injury and/or property damage.

The opener is not showerproof - it should not be
immersed in water or sprayed directly by a hose or other
water carrying device.

The door must be 

WELL BALANCED

and in good

working order. A faulty door must be repaired by a 
qualified technician prior to opener installation.

REMOVE OR DISENGAGE

all locks and 

mechanisms prior to installation of the opener.

Keep hands and loose clothing 

CLEAR

of the door and

opener at all times.

When using auto close mode a 

PHOTO ELECTRIC

BEAM

must be fitted correctly and tested for operation

at regular intervals. 

EXTREME CAUTION

is 

recommended when using auto close mode. 

ALL

SAFETY RULES 

above must be followed.

In order for the opener to 

SENSE 

an object obstructing

the doorway, some 

FORCE

must be exerted on the

object. As a result the object, door and/or person may
suffer 

DAMAGE or INJURY

.

Make sure that the door is fully open before driving into
or out of the driveway. And make sure the door is fully
closed before leaving the driveway.

The opener is not intended for use by young children or
infirm persons without adequate supervision. Children
should be supervised to ensure that they do not play with
the remote transmitters or the opener.

Frequently examine the installation, in particular  guides
and mountings for signs of wear, damage or imbalance.

DO NOT

use if repair or adjustment is needed since a

fault in the installation or an incorrectly balanced door
may cause injury. 

Summary of Contents for Pro Series 1100





























Reviews: