background image

189-9200235 A

A794-D110

01/99

TM

Federal Communications Commission (FCC) Radio Frequency Interference Statement Warning

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.

Note

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his
own expense.

Information to the User

This equipment must be installed and used in strict accordance with the manufacturer’s instructions. However, there is no
guarantee that interference to radio communications will not occur in a particular commercial installation. If this equipment does
cause interference, which can be determined by turning the equipment off and on, the user is encouraged to contact Axiohm
immediately.

The Axiohm company is not responsible for any radio or television interference caused by unauthorized modification of this
equipment or the substitution or attachment of connecting cables and equipment other than those specified by Axiohm. The
correction of interferences caused by such unauthorized modification, substitution or attachment will be the responsibility of
the user.

In order to ensure compliance with the Product Safety, FCC and CE marking requirements, you must use the power supply,
power cord, and interface cable which are sold for use with this product or which meet the following parameters:

Power Supply

UL Listed (QQGQ), Class 2 power supply with SELV (Secondary Extra Low Voltage), non-energy hazard output, limited energy
source, input rated 100-240 Vac, 1.5/0.8 A, 50/60 Hz, output rated 24 Vdc, 2.3 A.

Use of this product with a power supply other than the Axiohm power supply will require you to test the power supply and Axiohm
printer for FCC and CE mark certification.

Communication Interface Cable

A shielded (360 degree) interface cable must be used with this product. The shield must be connected to the frame or earth
ground connection or earth ground reference at EACH end of the cable.

Use of a cable other than described here will require that you test the cable with the Axiohm printer and your system for FCC
and CE mark certification.

Power Cord

A UL listed, detachable power cord must be used. For applications where the power supply module may be mounted on the floor,
a power cord with Type SJT marking must be used. For applications outside the US, power cords which meet the particular
country’s certification and application requirements should be used.

Use of a power cord other than described here may result in a violation of safety certifications which are in force in the country
of use.

Industry Canada (IC) Radio Frequency Interference Statement

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

Disclaimer

Information in this document is subject to change without notice. Consult your Axiohm sales representative for information that is
applicable and current. Axiohm reserves the right to improve products as new technology, components, software, and firmware
become available.

No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any
purpose without the express written permission of Axiohm.

Copyright

Copyright © 1999 by AXIOHM
Ithaca, New York USA. All rights reserved. Printed in USA. Confidential, Unpublished. Property of AXIOHM.

Trademarks

AXIOHM is a trademark of AXIOHM IPB, Inc.. Other trademarks and registered trademarks are the property of their
respective holders.

Summary of Contents for A794









Reviews: