44 |
A x i o m T o o l G r o u p
Symptom
Possible Cause
Correction *
Controller display is
blank or flickering.
Cable connections not tight.
Inspect and tighten connections between
pendant and control box.
Loose 24V connection to control
board.
Check the 24V connection to the DSP
control board in the control box.
Interface damaged.
Replace damaged part.
Controller damaged.
Replace controller.
Controller keeps
restarting automatically.
Insufficient power supply.
Have qualified electrician check incoming
power supply.
Local power grid unstable.
Contact power company.
Controller damaged.
Connect controller to computer via USB
cable. If problem still occurs, replace
controller.
Controller display reads
“Out of Limit”.
HOME operation has not been
performed.
HOME all axes and retry.
Design too large to fit within
machine limits.
Check ORIGIN placement and design
size.
Incorrect table size.
Check table size parameters in Machine
Setup.
Cannot set work origin
on controller.
May be in Machine Coordinate State Press MENU + 1 to revert to first working
coordinate system.
Buttons not functioning.
Enter
MENU
/System Setup/Buttons
Check to verify function. If buttons not
working, replace controller.
Z-axis fall is too fast
during processing.
Working speed exceeds Z-axis
maximum speed.
Set to safe speed in:
MENU
/Machine
Setup/Max Speed Limit.
Loose coupling, or transmission
slipping.
Tighten connecting parts.
Incorrect plunge speed in design
software.
Check speeds and verify correct post
processor is being used.
Z-axis depth not
consistent each time
same file is processed
and after machine
homes.
Spoil board or material not flat.
Re-mill (surface) spoil board/material
Workpiece not consistent thickness Check consistency
Interference in Z-axis HOME process
is creating a false origin.
Re-HOME Z-axis and check for proper
operation.
Processed workpiece
does not match file size.
Pulse equivalent incorrect.
Adjust pulse under:
MENU
/Machine
Setup.
Incorrect post processor
Verify that correct post processor was
used.
Wrong cutting tool used.
Use proper tool for process.
Summary of Contents for AR16 ELITE
