background image

 

AVG MAX MIN 

MAX MIN 

Indicating the display value being the current value(MAX 
MIN),the maximum value(MAX),the minimum value(MIN) and 
the average value(AVG) 

 

Indicating it is now in the data-holding state 

 

Warning symbol that the input signal is the high-voltage 

AC 

Indicating it is now in the AC measurement state 

DC 

Indicating it is now in the DC measurement state 

10 

 

Indicating the measurement value being negative 

11 

 

Indicating the overload in the insulation resistance 
measurement 

12 

AUTO RANGE 

Indicating the measurement being automatic range 

13 

MANUAL 

RANGE 

Indicating the measurement being manual range 

14 

2500V 

1000V 

Indicating the range of excitation voltage when performing 
the insulation resistance measurement 

15 

TEST 

Indicating it is now in the insulation resistance measurement 
state 

16 

 

Indication to low voltage of the batteries, showing the 
energy of batteries will be exhausted soon 

17 

 

The display zone for the meter’s measurement value, 
showing all the measurement values 

18 

51000 

Indicator of range, indicating the full range value of this 
range in manual range such as 5, 50, 500 and 1000,5000, 
etc. 

19 

-1888VDC 

Real-time display of the excitation voltage value when 
performing the insulation resistance measurement 

Function Descriptions 

Along with the conventional measurement functions this meter also possesses some special 
functions which being described as follows: 

 

True effective value (TRUE RMS) measurement: all the measurement values of this meter on the 

Summary of Contents for AX-TI220













Reviews: