background image

 

 

When rotary switch being in the positions of mV, logic frequency, diode, resistance and 

capacitance, the maximum overload protection voltage will be 250V(effective value),while in the 
positions of µA/mA the protection current being 0.64A,and in the position of A. 

 

Over range indication OL. 

 

When the total voltage of batteries being lower than 6.8V, the symbol for battery display will be 

lighted. 

 

Fuse being 0.63A/600V(µA/mA end) . 

 

Six 7# AAA batteries X 6. 

 

Operating temperature: 

 

0

30

 (relative humidity 0

80%) 

 

 

 

 

31

51

 (relative humidity 0

50%) 

 

Storage temperature: 

 

-20

60

 (relative humidity <= 80%) 

 

Altitude: 

operation  

less than 2000m, 

 

 

Storage   

less than 10000m 

 

Volume

 

 

 

200mm X 100mm X 40mm 

 

Weight

 

 

 

560g 

Range and Accuracy 

The below-listed accuracies under different ranges refer to those which are guaranteed by the 

meter within one-year calibration, with normal use under the operating temperature of 18

-28

 

and relative humidity less than 80%.The presentation for accuracy is: ± (**% reading  number 
of lower digits) 

 

AC Voltage 

Range 

Resolution 

Accuracy 

40Hz~400Hz 

500mV 

0.1mV 

±(0.8% +4) 

5V 

1mV 

±(0.8% +4) 

50V 

10mV 

±(0.8% +4) 

500V 

0.1V 

±(0.8% +4) 

1000V 

1V 

±(1.0% +4) 

Notes: above accuracies can be guaranteed within 10%-100% of the full range. 

 

DC Voltage  

Range 

Resolution 

Accuracy 

500mV 

0. 1mV 

±(0.1% +2) 

Summary of Contents for AX-TI220













Reviews: