Axis AXIS 570 User Manual Download | Manualshive

Page: 229 / 316

background image

AXIS 5470e/570/670e

User’s Manual

Section 14: Upgrading the software

229

Upgrading over the

Network using FTP

To upgrade over the network using FTP you will need the file with the
new print server software. The name of this file is in the form

product_version.bin

, e.g.

5470e_620.bin

for software release

6.20. You can use any of the previously mentioned methods to obtain
the new file.

You must assign the AXIS 5470e/570/670e with an IP address, as
described in

Assigning an IP address,

on page 32, before you can use

this upgrading method.

Follow the procedures below to upgrade the AXIS 5470e/570/670e:

Notes:

1. Log in to the AXIS 5470e/570/670e with the

command:

ftp <host name>

, or

ftp <IP address>

2. You will be prompted for user id and password. Use the user id

root

, which has the default password

pass

.

3. Type the command

binary

to change to binary transfer mode.

4. Type the command

put <software name> flash

, where

<software name>

is the name of the new print server software,

e.g.

5470e_558.bin

5. Wait for the Flash loading operation to finish. This normally

takes 1 to 4 minutes. The unit automatically restarts with the new
print server software.

6. Log out using the command

quit,

bye

or

exit

depending on

your FTP version.

•

If the upgrading process fails, simply try again.

•

If you lose contact with the AXIS 5470e/570/670e after an upgrading failure,
just restart the print server by disconnecting and reconnecting the power
supply to restore contact.

•

If the network diode flashes at half second intervals, the AXIS
5470e/570/670e cannot process any print jobs. To leave this state you must
repeat the instructions below.

«
...
227
228
229
230
231
...
»

Summary of Contents for AXIS 570





























































































































































































































































































































Reviews:

No comments

Related manuals for AXIS 570

Express5800/180Ra-7

Brand: NEC Pages: 2

Express5800/120Rh-2

Brand: NEC Pages: 2

Express5800/120Rh-2

Brand: NEC Pages: 2

Express5800/120Rg-1

Brand: NEC Pages: 2

Express5800/120Rf-1

Brand: NEC Pages: 21

Express5800/120Ra-1

Brand: NEC Pages: 6

Express5800/120Mc2 series

Brand: NEC Pages: 2

EXPRESS5800/120Le

Brand: NEC Pages: 56

Express5800 320La

Brand: NEC Pages: 8

Express5800 120Li

Brand: NEC Pages: 2

Express5800 120Ed

Brand: NEC Pages: 29

Active Upgrade Express5800/320Fc

Brand: NEC Pages: 4

Brand: NEC Pages: 10

Express5800/120Rj-2

Brand: NEC Pages: 18

Express5800/120Rh-1

Brand: NEC Pages: 20

Bull NovaScale R620 Series

Brand: NEC Pages: 346

Express5800 320La

Brand: NEC Pages: 206

Express5800/R110j-1

Brand: NEC Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands