Axis AXIS 570 User Manual Download

Page: 271 / 316

AXIS 5470e/570/670e User’s Manual

Appendix F: IPDS Overview

271

PostScript

output bin settings

These parameters are for mapping the IPDS bin numbers to the bin
numbers of the connected postscript printer.

IPDS PCL

Configuration

Click the

IPDS PCL Driver Settings

tab and enter the configuration

settings for the parameters as described below. When you are finished,
click

at the bottom of the page to save your settings to the print

sever.

Language version

Select the correct PCL language version depending on your connected
printer.

Symbol set

Select the preferred symbol set from the drop-down list. The default
and recommended value is

AUTOMATIC

. The print server will

automatically select the appropriate symbol set.

PCL bin 1-5

Define the positioning by setting the parameters

Horizontal Offset

and

Vertical Offset

to the desired values.

PCL Output Bin

These parameters are for mapping the IPDS bin numbers to the bin
numbers of the connected PCL printer.

IPDS Fonts

This section describes how IPDS fonts are handled by the AXIS
5470e/570/670e. There are two different approaches to font handling:

•

downloading fonts from the host.

•

using fonts that are already resident in the printer.

Both methods are supported by the AXIS 5470e/570/670e.

Summary of Contents for AXIS 570





























































































































































































































































































































Search results

Summary of Contents for AXIS 570

Reviews:

Related manuals for AXIS 570

Brands by name

Popular brands

Axis AXIS 570, User Manual

Search results

Summary of Contents for AXIS 570

Reviews:

Related manuals for AXIS 570

Brands by name

Popular brands