AXIS Q1775-E Network Camera
ハ
ハ
ハー
ー
ード
ド
ドウ
ウ
ウェ
ェ
ェア
ア
アの
の
の設
設
設置
置
置
壁
壁
壁面
面
面ブ
ブ
ブラ
ラ
ラケ
ケ
ケッ
ッ
ット
ト
トの
の
の取
取
取り
り
り付
付
付け
け
け
壁面ブラケットを取り付けるには、以下の手順に従います。
注意
•
カメラの重量は3.6 kgです。 この重量を十分に支えられる材質かどうかを
確認してください。
•
本製品とエンドポイントは、屋外用のシールドネットワークケーブル (STP) を
使用して接続してください。また、エンドポイントが適切に接地されている
ことを確認してください。 シールドネットワークケーブル (STP) と適切に接地
されたエンドポイントを使用して本製品を設置した場合、サージ保護など、
業界の耐性基準レベルを満たすことが確認済みです。 他の方法で取り付けを
行うと、保証の対象外となり、装置に問題が発生するおそれがあります。
•
オプションのケーブル (直径 4.0~5.5 mm) は、個別のケーブルグランドで
配線する必要があります。
を参照して
ください。
1. ドリルテンプレートとして壁面ブラケットを使用して、壁面ブラケットを
取り付ける準備を行います。
2. ネットワークケーブルを壁面ブラケットとブラケットアダプターに通しま
す。 カメラとの接続用に30 cmほどケーブルを残します。
3. 材質 (木材、金属、シートロック、石材など) に適したネジとプラグを使用
して、壁面ブラケットを壁、天井、または支柱に取り付けます。
ネ
ネ
ネッ
ッ
ット
ト
トワ
ワ
ワー
ー
ーク
ク
クケ
ケ
ケー
ー
ーブ
ブ
ブル
ル
ルお
お
およ
よ
よび
び
び他
他
他の
の
のケ
ケ
ケー
ー
ーブ
ブ
ブル
ル
ルの
の
の配
配
配線
線
線
注意
以下の手順に従う際は、ハードウェア概要イメージ (
を参照) を
参照してください。
1. ケーブルカバーのネジをゆるめ、ケーブルカバーを裏蓋から取り外します。
2. 使用するケーブルグランドからキャップ、プラグ、ガスケットを取り外
します。
3. ネットワークケーブルをキャップに通します。
4. ネットワークケーブルをガスケットの溝に沿ってスライドさせます。
5. ネットワークケーブルをケーブルグランドに通します。
6. ガスケットをケーブルグランドの中まで押し込み、キャップをしっかりと
締めます。
109
òò
¨¨
¾¾
Summary of Contents for Q1775-E
