AXITEC AXIbox 11K Installation And Operation Manual Download

Page: 11 / 13

Installationsanleitung AXIbox 11K

EN211103

7 Troubleshooting

7.1 Error detection via LED-indicator

State

Description

LED State

Standby

Normal

Flashing green, 1S on, 4S off

Charging

Normal

Breathing green, 1S on, 1S off

Cable connected

Normal

Breathing yellow, 1S on, 1S off

Software upgrade

Normal

Green light flash

Ground warning

Normal

Flashing yellow, 2S on, 2S off

Relay adhesion

Fault

Red light normally on

Input polarity reverse

Fault

Flashing red, 500ms on, 500ms off, 1 time, 3S off, Cycle

CP fault

Fault

Flashing red, 500ms on, 500ms off, 2 times, 3S off, Cycle

Leakage current fault

Fault

Flashing red, 500ms on, 500ms off, 3 times, 3S off, Cycle

Input terminal

overtemperature

Fault

Flashing red, 500ms on, 500ms off, 4 times, 3S off, Cycle

Relay overtemperature

Fault

Flashing red, 500ms on, 500ms off, 5 times, 3S off, Cycle

Under voltage fault

Fault

Flashing red, 500ms on, 500ms off, 6 times, 3S off, Cycle

Over voltage fault

Fault

Flashing red, 500ms on, 500ms off, 7 times, 3S off, Cycle

Overload fault

Fault

Flashing red, 500ms on, 500ms off, 8 times, 3S off, Cycle

Over frequency fault

Fault

Flashing red, 500ms on, 500ms off, 9 times, 3S off, Cycle

Other frequency fault

Fault

Flashing red, 500ms on, 500ms off, 10 times, 3S off, Cycle

Leakage current loop

abnormal

Fault

Flashing red, 500ms on, 500ms off, 11 times, 3S off, Cycle

Summary of Contents for AXIbox 11K














Search results

Summary of Contents for AXIbox 11K

Reviews:

Related manuals for AXIbox 11K

Brands by name

Popular brands

AXITEC AXIbox 11K, Installation And Operation Manual

Search results

Summary of Contents for AXIbox 11K

Reviews:

Related manuals for AXIbox 11K

Brands by name

Popular brands