background image

What’s Included

03

Safety Precautions

Good Working Practices/Safety

The following suggestions will enable you to observe good working practices, keep yourself and fellow workers
safe and maintain your tools and equipment in good working order.

WARNING!!  KEEP TOOLS AND EQUIPMENT OUT OF THE REACH OF YOUNG 

CHILDREN

Air Powered Tools

1. Always perform pre-operation checks before
starting up the compressor.

2. Never leave inflammable objects or materials near
to the compressor.

3. Always check oil level before using the
compressor.

4. The cylinder, cylinder head and delivery pipe
become hot during use. Do not touch these items
while the compressor is running.  Allow to cool 
thoroughly after shut-down before handling.

5. Do not operate above the maximum working
pressure of 115 psi (7.8 bar).

6.  Avoid using the compressor with an extension
cable; this may reduce the supply voltage and make
the motor overheat. 

7. Switch the compressor on and off by using the
pressure switch knob (Fig 3); only switch off at the
mains in case of emergency.

8. Drain water from tank every day.

9. If the compressor shuts down through overload or
overheating check the reason for the shut-down

before re-starting.

10. Do not adjust the tank pressure switch without
reference to Axminster Power Tool Service
Department. 

11. Do not remove parts from the compressor whilst
it is running.

12. Do not operate the compressor with protective
covers removed or damaged.

13. When spray painting always work in a well
ventilated area and never close to open flames.

14. Never direct a jet of compressed air towards 
people or animals. Keep children and animals away
from the compressor.

15. Do not use on an inclined surface.

16. Only use in ambient temperatures between –40˚C
and +70˚C.

17. Only operate on 230 volt supply and with
maximum fuse rating of 13 amps.

Quantity

Item

Model Number

1 off: 

Air Compressor 

4 off Small Washers 

(D)

RAC106B

1 off 

Bottle of oil  

4 off M6 Spring Washers 

(E)

4 off 

Rubber Feet 

(A)

4 off M6 Nuts

(F)

4 off 

M6x25mm Bolts 

(B)

1 off  Filter 

(G)

4 off 

M6 Large Washers 

(C)

1 off Instruction Manual

Summary of Contents for AWC10HP













Reviews: