background image

AB-6529 

11 

Maintenance (Lithium Battery Replacement) 

Replace the lithium battery for backup (Part No. 83104934-001) every 5 years. 

IMPORTANT: 

  Since the remaining battery capacity cannot be checked by measuring the terminal voltage, be sure to replace 

the battery every 5 years. 

  Only authorized service personnel is allowed to replace the battery. 

  Do not touch the power supply unit when replaceing the battery. 

  Replace the lithium battery every 5 years if the product is always in use (in ON state). 

  Replace the lithium battery with the power ON. 

  If the product has never or hardly been operated (in OFF state) for a year, replace the lithium battery before the 

product operation. 

 

Battery replacement 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  Replace the lithium battery while Infilex GD is ON. 

Figure 11.  Battery replacement 

 

1)  Pull out the battery holder using a slotted screwdriver. 

2)  Disconnect the connector and detach the lithium battery from the battery holder. 

3)  Place a new lithium battery in the battery holder and connect the connector to it. 

4)  Insert the battery holder into the basic unit. 

5)  Fill in the date for next replacement (5 years after the replacement) on the indication tag using an oil-based pen. 

 

1)

4)

5)

3)

2)

Infilex GD 
basic unit 

Lithium battery 
for backup 

Battery holder       Battery Connector 

Summary of Contents for Inflex GD WY5110













Reviews: