AB-5702
5
Specifications
Basic specifications
Item Specification
Rated voltage
100 V AC to 240 V AC, 50 Hz/60 Hz
Operating voltage
85 V AC to 264 V AC, 50 Hz/60 Hz
Power supply
Power consumption
6 VA
Ambient temperature
0 °C to 50 °C
Ambient humidity
10 %RH to 90 %RH (non-condensing)
Environmental
conditions
Vibration 19.6
m/s
2
max. at 16.7 Hz for 0.2 hrs
Ambient temperature
-20 °C to 60 °C
Ambient humidity
10 %RH to 90 %RH (non-condensing)
Vibration (transport)
9.8 m/s
2
max. at 10 Hz to 150 Hz (in package)
Transport/storage
condition
Vibration (storage)
3.2 m/s
2
max. at 10 Hz to 150 Hz
Installation of location
Inside of a control panel
Normal
Flashing every second
SC-bus error
Flashing every 0.25 seconds
Initializing ON
Major alarm
ON
Minor alarm
Repetition of 1 second ON and 0.25 second OFF
LED indications
Power OFF
OFF
Weight
230 g (without package)
Material
Modified PPE resin
LED: Light-emitting diode
PPE: Polyphenylene ether
Input/output specifications
Item I/O
specification
Connection
Wire specification
Status alarm input
Applied current/voltage: 5 mA DC typ./12 V DC typ.
Connectable output: Dry contact, transistor output
M3.5 terminal JIS CVV 1.25 mm
2
or JIS IV 1.25 mm
2
Max. 50 m long
ON/OFF output
Output type: Relay output (dry N.O. contact)
Contact rating: Max. 125 V AC, 2 A
(Inductive load: COSø = 0.4 or more)
Max. 250 V AC, 1 A
(Inductive load: COSø = 0.4 or more)
Minimum applicable load: 10 mA
M3.5 terminal Max. 60 V AC/DC:
JIS CVV 1.25 mm
2
or JIS IV 1.25 mm
2
Min. 60 V AC/DC:
JIS CVV 2.0 mm
2
or JIS IV 2.0 mm
2
Max. 50 m long
Totalizer pulse input
Pulse width: Min. 30 ms ON time
Min. 30 ms OFF time
Min. 100 ms ON+OFF time
Applied current/voltage: 5 mA DC typ./12 V DC typ.
Connectable
output: Dry contact, transistor output
(open collector output)
Memory backup: Replaceable lithium battery
M3.5 terminal JIS CVV 1.25 mm
2
or JIS IV 1.25 mm
2
Max. 50 m long
1–5 V DC input
Input impedance: 100 k
Ω
Isolation: Not isolated from other inputs
M3.5 terminal JCS CVV-S 1.25 mm
2
or
JCS CPEV-S
⌀0.9 mm
Max. 50 m long
4–20 mA DC input
Input impedance: 300
Ω
Isolation: Not isolated from other inputs
M3.5 terminal JCS CVV-S 1.25 mm
2
or
JCS CPEV-S
⌀0.9 mm
Max. 50 m long
Pt100 input
Input type: Resistance Temperature Detector (Pt100)
Sensing range: -20 °C to 80 °C
M3.5 terminal JCS CVV-S 1.25 mm
2
Max. 50 m long (The difference between
each wiring must be within 50 cm.)
Remote control relay drive
output
Output type: Thyristor output (dry contact)
Operating circuit voltage: 24 V AC
Output rating: Max. 1.5 A
Number of connection: 1 remote control relay
per
1
output
M3.5 terminal JIS CVV 1.25 mm
2
or JIS IV 1.25 mm
2
Max. 50 m long
Communication
Transmission method: Pole response voltage
transmission
Transmission speed: 4800 bps
Connector*
1
LAN
cable*
2
Power supply
Rated voltage: 100 V AC to 240 V AC, 50 Hz/60 Hz
Operating voltage: 85 V AC to 264 V AC, 50 Hz/60 Hz
M3.5 terminal JIS CVV 2.0 mm
2
or JIS IV 2.0 mm
2
Ground
Ground resistance: Max. 100
Ω
M3.5 terminal JIS CVV 2.0 mm
2
or JIS IV 2.0 mm
2
Notes:
*1 For connector connection, use Bel Stewart Connector’s Plug: Model SS-37000-002.
This plug is also available at Azbil Corporation. (Part No. DY7207A0100, 100 pieces/set)
*2 LAN cable compliant with EIA/TIA-568 Category 3 or over (
⌀
0.5 mm x 4 pairs) is required.
For *1 and *2, the connector cable (regular cable: Part No. DY7210, short cable: Part No. DY7220) are available at Azbil Corporation.
