background image

IQ Switch

®

 ProxSense

®

 

 
 

Copyright © Azoteq (Pty) Ltd 

AZD063 

Page 9 of 9      

All Rights Reserved. 

Azoteq RS100 Overview v0.01 

May 2012 

 
 
 
 

The following patents relate to the device or usage of the device: US 6,249,089 B1, US 6,621,225 B2, US 6,650,066 

B2, US 6,952,084 B2, US 6,984,900 B1, US 7,084,526 B2, US 7,084,531 B2, US 7,119,459 B2, US 7,265,494 B2, US 

7,291,940 B2, US 7,329,970 B2, US 7,336,037 B2, US 7,443,101 B2, US 7,466,040 B2, US 7,498,749 B2, US 7,528,508 

B2, US 7,755,219 B2, US 7,772,781, US 7,781,980 B2, US 7,915,765 B2, EP 1 120 018 B1, EP 1 206 168 B1, EP 1 308 

913 B1, EP 1 530 178 B1, ZL 99 8 14357.X, AUS 761094 

IQ Switch®, ProxSense®, LightSense™, AirButton® and the 

 logo are trademarks of Azoteq. 

 

The information in this Datasheet is believed to be accurate at the time of publication. Azoteq assumes no liability 

arising from the use of the information or the product. The applications mentioned herein are used solely for the 

purpose of illustration and Azoteq makes no warranty or representation that such applications will be suitable 

without further modification, nor recommends the use of its products for application that may present a risk to 

human life due to malfunction or otherwise. Azoteq products are not authorized for use as critical components in 

life support devices or systems. No licenses to patents are granted, implicitly or otherwise, under any intellectual 

property rights. Azoteq reserves the right to alter its products without prior notification. For the most up-to-date 

information, please refer to 

www.azoteq.com

WWW.AZOTEQ.COM

 

ProxSenseSupport@azoteq.com

 

 

Summary of Contents for IQ Switch ProxSense RS100










Reviews: