background image

User Manual 

Page 32

 

of 44 

connect  the  devices  as  shown  in  the  following  figure  so  that  the  physical 

connection  between  my  PC  and  my  company’s  server  is  achieved.  To  surf 

the  Internet  and  visit  my  company’s  network  at  the  same  time,  I  need  to 

configure the static routing. 

 

(1) Go to Advanced Setup > Routing > Static Route and Click add. 

(2)  Select  your  current  WAN  Interface  and  choose  from  connection 

name. 

(3) Click Add to add a new static routing entry. Finish the settings 

according to the following explanations: 

 

(4) Select the check box to enable this entry. 

(5) Click Apply to save the settings. 

 

FIELD 

DESCRIPTION 

Destination IP 

The destination IP address that you want to assign to a static route. 
This IP address cannot be on the same subnet with the WAN IP or 
LAN IP of the router. In the example, the IP address of the company 
network is the destination IP address, so here enters 172.30.30.1. 

Subnet Mask 

Determines the destination network with the destination IP address. 
If the destination is a single IP address, enter 255.255.255.255;   
otherwise, enter the subnet mask of the corresponding network IP. 
In the example, the destination network is a single IP, so here enters 
255.255.255.255. 

Gateway 

The IP address of the gateway device to which the data packets will be 
sent. This IP address must be on the same subnet with the router’s IP 
which sends out the data. In the example, the data packets will be sent to 
the LAN port of 

Router 2 and then to the Server, so the default 

gateway should be 192.168.1.2

 

Summary of Contents for VDSL5040GRV(AC)













































Reviews: