background image

 

4-6

Global Control Bar 

Each control items on this 

bar affects the adapter or management GUI directly. 

Show Tray Icon 

Making this item to be checked, the management GUI will minimize and stay on the 

tray icon located at the right down corner of Windows while pressing 

Close

 button. In 

other word, management GUI will shut down while pressing 

Close

 button with 

unchecked condition. 

Windows Zero Config 

Help switching to Microsoft Windows 

®

 XP Wireless network configure service if you do 

not prefer applying AsusWLAN as your wireless LAN manager. The detail steps you 

should follow are described in section 4.5. 

Radio Off 

Turn off the radio for saving power. While the radio being off, the links with other 

wireless network nodes are disconnected. User should be care of it while the wireless 

configuration is in AP mode. The radio off will cause the sub network belong to the AP 

to disconnect with internet/intranet. 

Disable Adapter 

Make this wireless LAN adapter being functionless for increasing better system 

resource management on performance and CPU utilization. 

Close 

Shutdown or hide the management GUI. The behavior depends on the check box of 

Show Tray Icon

Status Bar 

The status bar presents the hints or status of the management GUI. 

 

4.3 

Station mode 

Two types, Ad-Hoc and infrastructure in station mode could be configured through 

WiFi-AP Solo 

Wizard

. The following two sections explain the operation of management GUI for each type. 

The following explanations focus on the properties area.

   

 

Summary of Contents for AW-GA821

















































Reviews: