background image

 

30

Federal Communication Commission Interference Statement 

 

This equipment has been tested and found to comply  with the limits for a Class B digital 

device,  pursuant  to  Part  15  of  the  FCC  Rules.    These  limits  are  designed  to  provide 

reasonable  protection  against  harmful  interference  in  a  residential  installation.  This 

equipment generates, uses and can radiate radio frequency energy and, if not installed and 

used  in  accordance  with  the  instructions,  may  cause  harmful  interference  to  radio 

communications.    However,  there  is  no  guarantee  that  interference  will  not  occur  in  a 

particular  installation.    If  this  equipment  does  cause  harmful  interference  to  radio  or 

television reception, which can be determined by turning the equipment off and on, the user 

is encouraged to try to correct the interference by one of the following measures: 

 

Reorient or relocate the receiving antenna. 

Increase the separation between the equipment and receiver. 

Connect the equipment into an outlet on a circuit different from that 

to which the receiver is connected. 

Consult the dealer or an experienced radio/TV technician for help. 

 

FCC  Caution:  Any  changes  or  modifications  not  expressly  approved  by  the  party 

responsible for compliance could void the user's authority to operate this equipment. 

 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following 

two  conditions:  (1)  This  device  may  not  cause  harmful  interference,  and  (2)  this  device 

must  accept  any  interference  received,  including  interference  that  may  cause  undesired 

operation. 

 

IMPORTANT NOTE: 

FCC Radiation Exposure Statement: 

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled 

environment. This equipment should be installed and operated with minimum distance 

20cm between the radiator & your body. 

 

This transmitter must not be co-located or operating in conjunction with any other antenna 

or transmitter. 

 

Summary of Contents for AW-NU153H

































Reviews: