M
A
N 8
19
8
–2
11
01
4_
PD
11
-M-
1C
-F
LA
T_
EN
_1
21. Reset of the detector
If the permanent sabotage protection is activated,
the detector can be released again as follows:
•
Switch off the power supply and switch it back on
•
Let the sensor to initialize for 31 to 59 secs.
•
Switch off the power supply again
•
Apply power again and wait for for the self testing
•
Press the unlock
Pushing the „RESET“ button on the remote control, in opened mode,
will delete all of the values which was set by the remote control
(beside of INI ON/OFF) and set the detector back to
it‘s factory reset (500 lux, 10 min.).
18. Switch-off threshold brightness
1.
If the switch-on threshold has been modified by the potenti-
ometer or remote control, the switch-off threshold stored in
the EEPROM is deleted and is then recalculated on the next
activation.
Determining the switch-off value
1. Switch on for 5 min. with dark and motion
2. Light OFF for 2 sec.
3. Internal calculation of the switch-off value
2.
If the eye push button is pressed, the switch-off threshold is
recalculated. See also Remote control –> Eye section
3.
Switch-off delay
If the determined switch-off threshold is exceeded during
operation, the detector only switches off after a delay of ap-
prox. 15 minutes. This compensates for any brief fluctuations
in the brightness.
19a. Behaviour of external push button/
IR “Light“
The “Corridor“ and “Light ON/OFF“ functions are mutually
exclusive. If both are activated, the detector performs the cor-
ridor function.
The behaviour when the push button is pressed is defined as
follows:
Corridor function activated
Light ON:
Push button pressed briefly: Light OFF -> Active after 5 sec.
Push button held down: Light OFF -> Active after 5 sec.
Light OFF:
Push button pressed briefly: Light ON as long as Lag
time
Push button held down: Light ON as long as Lag time
Party function 12 h Light ON/OFF activated
Light ON:
Push button pressed briefly: Light OFF -> Active after 5 sec.
Push button held down: 12 h OFF
Light OFF:
Push button pressed briefly: Light ON as long as Lag time
Push button held down: 12 h ON
Corridor- und Party function 12 h Light ON/OFF deactivated
Light ON:
Push button pressed briefly: Light OFF as long as Lag time
Push button held down: Light OFF as long as Lag time
Light OFF:
Push button pressed briefly: Light ON as long as Lag time
Push button held down: Light ON as long as Lag time
19b.
Behaviour of external push button/IR
“Forced shutdown“
Forced shutdown active
Light OFF:
Light OFF: Push button pressed briefly: Light ON for approx.
30 min., then forced shutdown if the set brightness is still
exceeded.
20.
Fully automatic and semi automatic mode
HA
ON/OFF
(see functions IR-PD-1C)
Fully automatic operation
In this operating mode, the lighting switches automatically on
and off for increased comfort, depending on presence and
brightness.
- Channel 1 switches on in the event of motion if “dark“ is
detected.
Semi automatic operation
In this operating condition, in order to gain increased
savings, the lighting is energized only after being
manually switched on.
Switch-off takes place automatically or manually.
The semi automatic mode basically behaves like the fully
automatic one. However, the difference is that switching-on must
always be carried out manually!
As many (closer-contact) buttons as desired can be wired in
parallel on the “S” button input (ON/OFF).
Triggering in semi automatic mode:
If the detector switches
off in semi automatic mode (lag timer elapsed), the detector
is switched on again within 10 sec. by motion (despite semi
automatic mode).
LED function indicators after each mains recovery
(60sec. initialisation period)
Operating
state
LED function indicators
Factory pro-
gram active
White, red and green flash in quick
succession for 10 sec., then initialisation
indicators, see below
Indicator
unpro-
grammed
Indicator
program-
med
Indicator also
when forced shut-
down is activated
Standard
mode
–
red flashes
quickly
Every 5 sec., 4
x white, red and
green in quick
succession
12 h ON/
OFF active
Red and
green
flash
Red and
green
flash
quickly
Every 5 sec., 4
x white, red and
green in quick
succession
Corridor
active
Red and
white
flash
Red and
white
flash
quickly
Every 5 sec., 4
x white, red and
green in quick
succession
12 h ON/
OFF & corri-
dor active
Red, green
and white
flash
Red,
green
and white
flash
quickly
Every 5 sec., 4
x white, red and
green in quick
succession
CdS
active
–
Red and
white
flash
Then no red
LED for motion
detection
LED function indicators during operation
Process
LED function indicators
Semi-automatic mode active
White is ON
Corridor active
White ON 1 sec. and OFF
4 sec. aus
Corridor and semi-automatic
mode active
White ON 4 sec. and OFF
1 sec.
12 h ON/OFF function active Red and green flash
alternately
IR command
White flashes once
IR-command „Open“ and
Sabotage active
white and green
flashes once
Permanent on/off
red flashes
22.
LED-functional indicators remote control
PD11_NEU_4lang_211014.indd 3
04.12.2014 15:31:04
