background image

NEEDED

FOR 

INSTALLATION:

Warning

Flammable

Hot Surface

·  Suitable for wet locations

IMPORTANT LISTINGS AND CERTIFICATIONS

PVC Housing

Body

Faceplate

18/3 Ga. Wire

Stability Flange

Surface 

Mount Collar

Flush Mount 

Collar

Proper soil preparation is required before installation. See the DIG-IT guide at www.bklighting.com/collaterals/install/digit.pdf 

for more information.

High Voltage

Surface mount uplights are intended for installation in 

wood, pavers, stone, and other hardscapes.

Not recommended for concrete pour 

installations.

INSTALLATION

RELEASE DATE

08/16/2022

REFERENCE NUMBER

INS-2873-00

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900 

www.bklighting.com • info@bklighting.com

B-K LIGHTING

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR 

SELL ANYTHING IT MAY DESCRIBE.  REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION 

INSTRUCTIONS

• 

Product must be installed by a qualified person in a manner 

consistent with its intended use and in compliance with the 

National Electrical Code, Canadian Electrical Code, and all 

Local and Provincial Codes. 

• 

Follow product label information and instructions.

• 

Qualified Personnel must perform all servicing or relamping 

of this product.

•  Before wiring to power supply and during servicing or 

relamping, turn off power at fuse or circuit breaker before 

service.

•  The use of accessory equipment not recommended by the 

manufacturer or installed contrary to instructions may cause 

an unsafe condition. The use of damaged components may 

cause an unsafe condition and void product warranty.

• 

Do not block light emanating from product in whole or part, 

as this may cause an unsafe condition.

•  Never operate the fixture with missing or damaged lens.  

Lens must be cleaned on regular basis.

• 

Entire fixture may become extremely hot. Do not touch hot 

lens or fixture body. Do not touch the lamp at any time. Use 

a clean, dry, soft cloth to handle the lamp. Oil from skin 

may damage the lamp and cause it to rupture.

•  Replace lamp only with correct wattage and type of lamp 

marked on fixture label.

•  All gaskets, o-rings and sealing surfaces must be kept 

clean during installation and service; failure to do this may 

cause an unsafe condition and void product warranty. 

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL 

SAFETY AND INSTALLATION INSTRUCTIONS

INSTRUCTIONS PERTAINING TO

A RISK OF FIRE, OR INJURY

TO PERSONS IMPORTANT SAFETY 

INSTRUCTIONS

Lighted fixture is HOT!

WARNING - To reduce the risk of 

FIRE OR INJURY TO PERSONS: 

Turn off/unplug and allow to cool before 

replacing lamp/LED. Fixture gets HOT quickly! 

Contact only switch/plug when turning on. 

Do not touch hot lens, guard, or enclosure. 

Keep fixture away from materials that may burn.  

Do not operate the luminaire fitting with a missing or 

damaged shield.  Do not touch the source at any time. 

Use a soft cloth or gloves. Oil from skin may cause 

damage.

SAVE THESE INSTRUCTIONS

5/64”, 9/64” & .050” Allen Wrench
Waterproof Wire Connectors
Silicone

 

HUME

UPLIGHT - INTEGRAL

Standard Installation

Summary of Contents for HUME








Reviews: