background image

13

WARNING DANGER

The mounting of the burner on the boiler must be sealed to avoid any dangerous smoke escaping. Use the seal 
supplied by the manufacturer.

2.5 

Mounting of the loading cochlea and the pellet container

The mounting of the external loading cochlea and of the pellet container is very important if  the burner is to run correctly.
It is advisable to buy and use the original accessories, because they have been specifically designed to ensure the correct 
running of the burner.

WARNING

The manufacturer  

Elmec Group S.r.l.

 DOES NOT ACCEPT RESPONSIBILITY for any damage to people, animals or 

things caused by the use of components that are not original.

2.6 

Release of exhaust fumes

The burners

B-Home Round 25

 and 

B-Essential Round 50

 have been designed to operate solely with heat generators that have 

a vacuum combustion chamber, so the smoke duct and the flue must be designed and realised to satisfy these requirements.
The joints must be sealed and resistent to the maximum temperature levels that the fumes can reach.

WARNING DANGER

 

Any applications which are different from the one specified in the manual can cause  fire.

 

Non-insulated exhaust ducts are a potential source of danger.

 

It is possible to install a flue valve which conforms to applicable legislation

2.7 

Electrical connections

The burners

B-Home Round 25

 and 

B-Essential Round 50

 have been wired in the factory and it is essential that only profession-

ally-qualified personnel carry out the work reported below.

2

1

3 4 5 7

6

Power supply socket (230V~50Hz)

External cochlea fan power socket

External cochlea motor

Boiler water temperature probe

External thermostat connection

Connection for use with a PC

Connection for optional applications

WARNING DANGER ELECTRICITY

Please remember that  

IS OBLIGATORY

:

 

to use an omnipolar circuit breaker switch, a disconnect switch in conformity with EN regulations

 

to use an L (phase) - N (Neutral) connection

 

to connect the earth to an efficient plant grounding device. The manufacturer 

Elmec Group S.r.l.

 DECLINES ANY 

RESPONSIBILITY for any damage to people, animals or things, caused by the absence of grounding of the appli-
ance and of the non-compliance with anything specified in this manual.

IT IS FORBIDDEN

Use the water pipes for the grounding of the appliance.

Summary of Contents for B-Home Round 25

























Reviews: