background image

4

© B&S Commercial Kitchen Appliances Pty Ltd 2016

General Information;

These specifications cover the B&S ranges of Verro, Black and K+ Woks and Stock Pots.

We are confident that you will be delighted with your B&S Wok or Stock Pot, and that it will become the 

backbone of your kitchen. To ensure you receive the utmost benefit from your new B&S appliance, there are 

two important things you can do.

1.  Ensure you thoroughly read this booklet and ensure all instructions are followed. Ensure that this booklet  

      is kept in a safe and prominent location for future reference.

2.  Should you be unsure of any aspect of the operation, performance, servicing or installation of the appli-

ance, please contact your B&S dealer immediately. In most instances a phone call will answer your question.

THIS APPLIANCE SHALL ONLY BE INSTALLED/SERVICED BY AN AUTHORISED INSTALLER.

THIS APPLIANCE MUST BE INSTALLED IN ACCORDANCE WITH THE SPECIFIED INSTRUCTIONS 

AND SPECIFICATIONS.

IMPROPER INSTALLATION OR OPERATION OF THIS APPLIANCE MAY RESULT IN PRODUCT 

FAILURE WHICH MAY LEAD TO PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.

CAUTION MUST BE TAKEN WHEN OPERATING THIS APPLIANCE TO MINIMISE RISK OF FIRE.  

THE APPLIANCE MUST NOT BE LEFT ON UNATTENDED.

REGULAR INSPECTIONS BY AN AUTHORISED SERVICE PERSON ARE STRONGLY RECOMMEND-

ED TO ENSURE PROPER AND SAFE FUNCTIONING OF THIS APPLIANCE.

AFTER ANY SERVICING OR ADJUSTING OF GAS CONNECTED COMPONENTRY, GAS LEAK TEST 

MUST BE CARRIED OUT TO ENSURE THERE ARE NO GAS LEAKING HAZARDS.

NEVER STORE ANY FLAMMABLE LIQUIDS/VAPOURS IN THE VICINITY OF THIS APPLIANCE. 

NEVER SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION.

ENSURE ANY TRANSIENT PROTECTION IS REMOVED BEFORE INSTALLING THE APPLIANCE 

ENSURING ANY POSSIBLE DAMAGE TO THE APPLIANCE OR COMPONENTS/PARTS THAT MAY 

HAVE BEEN SUSTAINED DURING TRANSPORTATION IS REPORTED TO THE MANUFACTURER 

WITHIN SEVEN (7) DAYS OF RECEIPT OF UNIT

THIS APPLIANCE IS NOT INTENDED TO BE USED IN A MARINE ENVIRONMENT. 

ENSURE APPLIANCE IS INSTALLED IN A STABLE POSITION.

FAILURE TO FOLLOW THE INFORMATION PROVIDED IN THIS BOOKLET WILL VOID THE B&S 

WARRANTY AND MAY RESULT IN DAMAGE TO EQUIPMENT OR INJURY TO PERSONNEL

Summary of Contents for Verro Series














Reviews: