background image

 

 

INTRODUCTION 

You have recently purchased a BABOLAT SENSOR stringing machine - thank you for making 

the right choice! This manual has been written specially to help you get used to the way the 

machine works and to make sure that it meets your expectations. Please READ THESE 

INSTRUCTIONS  CAREFULLY  to  give  yourself  a  good  idea  of  the  precautions  to  be  taken 

when you use your new machine and to look after it in the best possible way. 

Keep this manual to hand

 so that you can consult it at any time, and make sure that it 

stays with the machine if ever lent or sold. 

A VHS video cassette comes with your SENSOR stringing machine. We suggest you to watch 

it in addition to reading this manual, so that you will have a good understanding of the main 

operations for setting up and using the machine, as well as the actions required for 

stringing. 

This machine is intended for professional use and is designed for the stringing of all types of 

rackets - tennis, badminton, squash, etc. - using strings made of synthetic materials or 

natural gut. It must be used by operators who are qualified and well-versed in the operating 

rules and safety instructions set out in this manual. 

Your SENSOR stringing machine is "CE" certified and is in conformity with machine directive 

89/392/EC. We will not assume liability if any alterations are made to the machine without 

our authorisation, thus undermining the safety conditions and invalidating any warranty 

clauses. 

We also wish to draw your attention to the fact that the use of accessories or products other 

than those recommended by BABOLAT may present risks for which we will not be liable. 

As we want you to make the most of the latest technology and new equipment, as well as to 

benefit from our experience, our machines may undergo technical or design changes. As a 

result, some of the features and information in this manual may be changed without prior 

notice and without any obligation to up-date it. 

Should you encounter any problems or have any questions about your SENSOR stringing 

machine, please do not hesitate to contact your nearest BABOLAT After-Sales Service 

Centre. 

Summary of Contents for Sensor Dual





























Reviews: