4
3
1. Place the appliance on a flat surface where it is out of reach of children
and it will not be knocked or moved during operation.
2. Remove the lid, and Bottle Tray from the sterilizer base.
3. Fill Measuring Cup to max line and pour 120ml/4oz water on the base/heater
surface. Do not overfill. We recommend using distilled water to avoid
mineral scale build-up on the heating plate. However, you can use bottled
water or tap water but you may need to descale more frequently.
4. Place the Bottle Tray on the base.
5. Place clean bottles with their opening facing downward over the nozzles on
the Bottle Tray (Do not place more than 6 bottles on the Bottle Tray).
6. Place accessories on the Accessory Tray (nipples, collars, caps, etc)
7. Place the Lid securely on the base.
8. Press the Button repeatedly to select your desired mode:
Sterilize & Dry , Sterilize Only , Dry Only
The selected function will start automatically after 3 seconds.
Automatic Sterilize & Dry Function:
Press the Button one time for Automatic Sterilize & Dry mode.
The red LED switches on and the Sterilize cycle runs for approximately 5m 30s.
After Sterilizing, the LED changes to blue, the Dry cycle begins automatically and
runs for approximately 4m 30s. After Drying the appliance turns off and enters
standby mode. If the button is pressed at any point during the cycle the appliance
stops and enters standby mode.
Sterilize Only Function:
Press the Button two times for Sterilize Only mode.
The red LED switches on and the Sterilize cycle runs for approximately 5m 30s.
After sterilizing the appliance turns off and enters standby mode. If the Button is
pressed at any point during the cycle the appliance stops and enters standby mode.
Set-up and Use
Prior to first use, wash Lid, Bottle Tray, Accessory Tray, and Measuring Cup.
Before placing items in the appliance for sterilization it is important that
all bottles, pump parts and accessories must be EMPTY, CLEAN & FULLY
RINSED BEFORE USE in this sterilizer dryer.
Standby mode: When the appliance is plugged in, all LEDs flash for 0.5 seconds
then enters standby mode.
Cleaning
- Always unplug the sterilizer dryer before cleaning.
- Do not immerse the base, the power cord or the plug in water or other liquids.
- Do not clean base under water tap.
- Use a soft damp cloth to clean the base and control console.
- Never use abrasive pads to clean the plastic parts of the machine.
- The Lid, Bottle Tray, and Accessory Tray can be cleaned in hot soapy water.
- Mineral residue, particularly in hard water areas, may deposit on the heating
plate after a few sterilization cycles. To avoid scale build up, wipe
the surfaces with a soft moist cloth after each operation.
- Deposits can be removed with scale removers or by leaving 60ml/2oz
water and vinegar solution (50/50 water & vinegar mix) on the heating
plate for approximately 30 minutes. The plate should then be wiped clean with
a clean, dry cloth. Some discoloration spots may remain after cleaning with a
vinegar solution, but these are harmless.
- Do not use abrasives or solvents for cleaning; they may damage the appliance
and the surface of the heating plate.
- Before plugging in the sterilizer again make sure the base unit is completely dry.
- The filter can be removed and rinsed clean with water once a week.
Make sure filter is completely dry before replacing.
After each use, pour away any remaining water from the base.
Always POUR AWAY FROM FAN OPENING.
Dry Only Function:
Press the Button three times for Sterilize Only mode.
The Blue LED switches on and the Dry cycle runs for approximately 6 minutes.
If the Button is pressed at any point during the cycle the appliance stops and
enters standby mode.
