background image

 Copyright © 2009 - 2010, Baby Trend Inc., All Rights Reserved.

 Copyright © 2009 - 2010, Baby Trend Inc., All Rights Reserved.

ASSEMBLY

SAFETY

5

6

the child tray must be rotated to the vertical 

position. Press red buttons on both sides of the 

child tray to rotate down 90 degrees. (Fig. 10)  

To remove the child tray:  

Pull both release levers located on the underside 

of each side of the tray and lift upward. (Fig. 11)

 

 

  

CUP HOLDER 

(sold separately) 

This is an optional accessory item that can be 

purchased online at www.babytrend.com. The 

removeable child tray can be replaced with 2 

individual cup holders. It is ideal for an older 

child. 

 

To attach the cup holder:  

Push the cup holder downward and onto each side 

of the front armrests until it snaps into place. 

 

(Fig. 12)

CANOPY 

To attach the canopy:

 

Line up the male fittings on the canopy with 

the slots on the armrest and push both fittings 

downward until snapped into place. (Fig.13) To 

open the canopy, push forward on the front edge 

of the canopy while holding the rear of canopy in 

place. To fold the canopy, pull backward on the 

front edge. 

 

To remove the canopy:

 

Press the snap button under the armrest and pull 

to release the fitting from the slot. Repeat for the 

other side.

PLATFORM

 

To attach platform:  

Squeeze both locking clips with both hands 

 

while holding the platform vertically (Fig. 14). 

Then slowly rotate the platform downward until 

it rests in place on the axle rod. Once in place 

release both locking clips. (Fig. 15)

 

 
Before placing your children in the stroller, 

please follow the instructions below.

WARNING:

 Always set 

brakes when the stroller is not being 

pushed so that the stroller will not 

roll away. NEVER leave stroller 

unattended on a hill or incline as 

the stroller may slide down the hill.

BRAKES 

To engage brakes, apply light downward pressure 

to the brake lever located on each rear wheel.  The 

stroller may require slight forward or rearward 

movement in order to line up the teeth on the 

brake with each wheel brake cluster.  (Fig. 16)  

Check that the stroller will not move and that both 

brakes are properly applied. To release, gently lift 

up on the brake lever. (Fig. 17)

TO SECURE THE CHILD

WARNING:

 Avoid serious 

injury from falling or sliding out. 

Always use the safety harness. 

STRANGULATION 

HAZARD:

  Child can 

strangle in loose straps.  Never leave 

child in seat when straps are loose 

or undone. 

TANDEM STOLLER - 5-Point Harness

• The shoulder straps of the 5-point harness 

has 2 attachment positions.  Select the loop 

Fig. 12

release lever

Underside of the child tray

Fig. 11

Fig. 13

Fig. 18

Fig. 14

Fig. 15

Fig. 16

Fig. 17

Fig. 10

red button

Summary of Contents for Sit N Stand D X







Reviews: