background image

All Restoration Hardware cribs are designed to meet the highest safety

standards and comply with all U.S. and Canadian cribs and cradles regulations.

Model No: 367-19

Haven Panel Crib

Made in Vietnam

Distributed in the U.S.A by:
Restoration Hardware Baby & Child

11640 Harrel St. Suite B

Mira Loma, CA 91752

www.rhbabyandchild.com

Distributed in Canada by:
Restoration Hardware Canada, Inc.

1500-1055 West Georgia Street
Vancouver, British Columbia V6E4N7

WARNING:

 

Read all

Instructions before assembling this

product.

 KEEP INSTRUCTIONS

FOR FUTURE USE.

CARE AND CLEANING

DO NOT

 scratch or chip the finish. 

DO NOT

 use abrasive chemicals for cleaning. Clean with mild soap on soft rag. Rinse

and dry thoroughly. If the crib is to be stored, store in a cool dry place and carefully package all original hardware to

protect from loss.

TOOLS AND INSTALLATION

Tools Necessary: Allen Key (included).

NOTE: It may be easier to assemble product with two people.

NOTE:

 When inserting bolts, turn clockwise until tight. Then loosen 1/2-3/4 of a turn. After crib is completely

assembled, return to each bolt and tighten. Use wax or soap on all bolts to facilitate assembly.

CUSTOMER SERVICE

If you are missing parts or have any questions about this product, contact us first. You can also order parts by writing to

the address above. Include the product model number, color, and a brief description of the part. Call 1-800-762-1751.

Page 1 of 9

Summary of Contents for 367-19










Reviews: