background image

Page 4 of 13

WARNING

Do not use this crib if the enclosed or attached instructions 

cannot be strictly adhered to. Do not use this crib if the child is 
able to climb out unaided or is taller than 90 cm. Do not place 
cords, straps or similar items that could become wound around 
the child’s neck in or near this crib. Ensure that the sides are
properly latched or locked in place when the crib is occupied. The 
mattress used with this crib should not be more than 15 cm thick
and should be of such length and width that the gap between the 
mattress and the sides of the crib is not more than 3 cm when the 
mattress is pushed into the corner of the crib. 

Parents should inspect the crib regularly −− before putting the 

child in the crib each day −− and confirm that every component of 
the crib is properly and securely in place.

IMPORTANT SAFETY INFORMATION FOR CRIBS

WARNING

Failure to follow these warnings and the assembly instructions could 
result in serious injury or death from entrapment or strangulation.  

DO NOT

place bed near windows where cords from blinds or drapes 

may strangle a child.

The mattress intended for use on the bed shall be a full−size crib mattress having 

minimum dimensions of 51−5/8 in. (1310 mm) in length, 27−1/4 in. (690 mm) in width and 4 
in. (100 mm) in thickness, not exceeding 6 in. (152 mm) in thickness. 

DO NOT 

place bed near windows where cords from blinds or drapes may strangle a child.

DO NOT

place items with a string, cord, or ribbon around a child’s neck, such as hood 

strings or pacifier cords.

DO NOT

suspend strings over a toddler bed for any reason.

FOR TODDLER BEDS AND DAY BEDS ONLY.

A child using this bed should be at least 

15 months of age and should not weigh more than 50 lbs. (22.7 kgs.).

IMPORTANT SAFETY INFORMATION FOR TODDLER & DAY BEDS

Summary of Contents for Sutton 5563-0612














Reviews: