BBT05-IM-090324
THIS PRODUCT IS INTENDED FOR
HOUSEHOLD USE ONLY
SAVE THESE INSTRUCTIONS
Generally, accepted “normal” temperature reading is 37.0°C /98.6°F, but
temperature readings differ to this figure may still be considered “normal”.
Variations in temperature can be attributed to activities such as exercise,
smoking, eating and drinking. Our temperature is lower in the morning than in
the afternoon. Other variations may be due to the location of the temperature
reading.
Method of measuring also varies the measured temperature as well and normal
temperature ranges are show as follows:
Oral 35.5-37.5˚C (95.9-99.5˚F)
Axillary (underarm)
34.7-37.3˚C (94.5-99.1˚F)
Rectal 36.6-38.0˚C (97.9-100.4˚F)
Ear 35.8-38.0˚C (96.4-100.4˚F)
When use the thermometer first time, open the battery cover as per the
“REPLACING THE BATTERY” section in this manual. Put 2 AAA (LR03)
batteries in the battery compartment with correct polarity. Replace the cover and
lock. It will switch ON automatically in the Stand-By Mode. The default time
setting is 12:00.
The thermometer can also be changed to Temperature Measure Mode.
Switching to this mode, the ear canal temperature and the forehead
temperature can be measured.
Details of operation in each mode are described in the following sections.
In the Stand-By Mode, the time display and the ambient temperature display
are shown on the LCD display screen alternately. The time display shows
the clock in hh:mm (24-hour) format. The ambient temperature display
shows the measured room temperature in temperature unit (°C or °F) that is
last used in the Temperature Measure Mode.
The time display and the ambient temperature display interchange every 20
seconds. If the thermometer is in the Temperature Measure Mode, it will
switch back to Stand-By Mode after left idle for 30 seconds.
In the Stand-By Mode, wait the display screen to show the time display.
Press and hold Button A for 2 seconds, the hour digits flash. Press Button B
to adjust the hour by advancing one hour.
Press Button A again will set the hour and swap the minute digits to flash.
Press Button B to adjust the minute by advancing one minute. Keep
pressing the Button B can increase the advancing pace at high speed.
Press Button A will interchange the adjustable unit (hour & minute). Press
and hold Button A will complete the time setting process. Stand-By Mode
resumes.
This thermometer is designed to receive the infra-red rays emitted by the skin
surface and in the ear drum. It provides a fast and accurate means for you to
check your baby’s temperature easily.
If the thermometer is in the Stand-By Mode, press Button B to change to
Temperature Measure Mode. The thermometer will briefly show all icons on
the display as per the image of “Fig. A”, and then thermometer will show
0.0˚C or 0.0˚F, this indicates the thermometer is ready for measure
temperatures. The measuring method (ear or forehead) follows the usage in
the last temperature measurement.
Press and hold Button A will interchange the measuring method between ear
and forehead.
Press and hold Button B will interchange the temperature unit between °C
and °F
Fig. B
Take off the protective cover, change thermometer to Temperature Measure
Mode. Select the measuring method to ear measurement and the preferred
temperature unit (°C or °F).
Insert the probe into the ear canal gently as per “Fig. B”.
Press Button B. The thermometer responses with a beep and it will
automatically read the ear temperature in around 2-3 seconds.
Once the measurement completed, the thermometer will beep again.
Measured temperature will then show on the display.
Note:
1. Please ensure the probe is inserted into ear canal to get an accurate
temperature measurement.
2. For optimal precision, ensure the ear is not obstructed by wax or a plug.
3. As usual for any measuring equipment, slight variations in temperature may
results for the measurement one after another. It is therefore recommended
to take several readings and take the highest in account (Withdraw the
thermometer from the pinna and press Button B briefly between each
reading). Measure again and new measured temperature will then show on
the display within another 2~3 seconds.
Fig. C
Take off the protective cover, change thermometer to Temperature Measure
Mode. Select the measuring method to forehead measurement and the
preferred temperature unit (°C or °F)
Place the probe to the middle of the forehead (just above the surface of the
skin) with the probe perpendicular to the skin as per “Fig. C”
Press Button B. The thermometer responses with a beep and it will take the
forehead temperature in around 2-3 seconds.
Once the measurement completed, the thermometer will beep again.
Measured temperature will then show on the display.
If measured temperature within normal range, thermometer will beep once
and then the peak temperature measured with a smiling face icon “
” will
show on the display to indicate normal temperature is measured.
Otherwise, if the measured temperature is above 38.0°C (100.4°F), the
thermometer will show an sad face icon “
” with the peak measured
temperature on the display, indicating a fever signal. In this case, you
should consult your physician.
Read and record the temperature after each measurement. Last 12
readings will be automatically stored in the memory for reference;
The thermometer will switch off automatically in 60 seconds if no button is
pressed again after it is activated by pressing the “Power On” button.
This thermometer can store last 12 temperature measurements.
To recall the memories, press Button A in Temperature Measurement Mode.
The memory icon “
” and a number will show on the display. The number
show on the display represents the temperature recorded in the memories.
“0” is the last memory and “1” is the second last and so on. Press
successively to scroll the memories.
1. The Lens is the most delicate part of the unit, and special care is needed
2. Clean the thermometer using soft dry cloth or cotton swab.
The battery in your infra-red thermometer needs to be replaced when “
”
appears on the display window.
To replace the battery
1. Remove the battery cover by turning the battery cover lock with a coin in
anti-clockwise direction.
2. Take out the old batteries from the thermometer and replace with the new one,
Ensure to fit the batteries with correct polarity. (Note: polarity mark of the
batteries are provided on the battery compartment for easy reference)
3. Replace the battery cover and turning the battery cover lock back in place.
NOTE: Always use environmental friendly way to dispose
batteries.
If measured temperature does not seem to be in normal range or unstable,
you should consult your doctor or physician to check your health condition.
Dimension (mm)
131.5(L) x 35.5(W) x 30(D)
Weight
70 grams (including batteries)
Measuring time
As short as 2-3 second. .
Measurement
range and
Precision
+/-0.2°C (0.4°F) for 36 - 39 °C (96.8 - 102.2 °F)
+/-0.3°C (0.5°F) for T <36°C (96.8°F), or >39°C (102.2°F)
Measurement
units
Measure in Centigrade (°C) or Fahrenheit (°F)
Display
Resolution
0.1 for both °C and °F
Battery
2 x LR03 /AAA size 1.5V batteries or equivalent
Operating
Condition
Temperature: 16 to 40 °C (60.8 to 104 °F)
Relative Humidity: < 85%
Storage Condition
Temperature:
–
10 to 55 °C (–14 to 131 °F)
Relative Humidity: < 85%
Other feature
With a lanyard hole for easy carrying and storage
This technical specification may subject to modification to improve the
thermometer, without prior notice.
FOREHEAD MEASUREMENT
HOW TO SET TIME
Stand-By Mode
SPECIAL NOTE
BEFORE FIRST USE
WHAT IS A “NORMAL” TEMPERATURE?
AFTER YOU GET THE READING
EAR MEASUREMENT
PRODUCT FEATURE & SPECIFICATION
REPLACING THE BATTERY
TEMPERATURE MEASURE MODE
RECALL THE MEASUREMENT STORED
GENERAL CARE
DO NOT hold the thermometer too
long, as it may affect and render
the measured temperature to lower
than usual.
