Bacharach H-10PA Manual Download

Page: 10 / 16

Replacing the Sensor:

The sensor is a disposble plug-in unit.
Replace it when the H10PA no longer
responds to the

CALIBRATION

REFERENCE

bottle, even with the sensor

HEATER

ADJUSTMENT

turned fully clockwise

(make sure the

CALIBRATION

REFERENCE

bottle contains some refrigerant).
1. Set the

POWER

switch to

OFF

2. Unplug the power cord if the unit

is plugged in and open the sensor
cover.

3. Allow the sensor to cool before handling.

4. Unplug and discard the sensor.
5. Insert a new sensor and close the

sensor cover.

6. Turn the sensor

HEATER

ADJUSTMENT

its full counterclockwise position.

7. Apply power to the unit and reset

the

HEATER

ADJUSTMENT

(see Section

Sensor Heater Adjustment).

Warning!

Personal Injury Hazard.

Sensor surface temperature may reach
390°F (200°C) during operation, and may
cause a burn if not allowed to cool.

Summary of Contents for H-10PA

















Search results

Summary of Contents for H-10PA

Reviews:

Related manuals for H-10PA

Brands by name

Popular brands

Bacharach H-10PA, Manual

Search results

Summary of Contents for H-10PA

Reviews:

Related manuals for H-10PA

Brands by name

Popular brands