background image

16 

OPERATION INSTRUCTIONS

STORAGE:

Between uses:

• 

Turn the control knob to “OFF” position.

• 

Turn LPG cylinder to “OFF” position.

• 

Store heater upright in an area sheltered away from weather conditions (such as rain, sleet, 

hail, snow).

• 

If desired, cover heater to protect exterior surfaces and to help prevent dust and debris 

collecting in air passages.

During periods of extended inactivity or when transporting:

• 

Turn the control knob to “OFF” position.

• 

Disconnect LPG Cylinder and move to a secure, well-ventilated location outdoors. DO NOT 

store in a location that will exceed 50 degrees C (122°F).

• 

Store heater upright in an area sheltered away from weather conditions (such as rain, sleet, 

hail, snow).

• 

If desired, cover heater to protect exterior surfaces and to help prevent dust and debris 

collecting in air passages.

FOR YOUR SAFETY:

•  DO NOT touch or move heater for at least 45 minutes 

after use.

•  Allow all burner elements to cool before touching.

 WARNING

In a salt-air environment (such as near an Ocean) 

corrosion occurs more quickly than normal.

•  Frequently check for corroded areas and repair them 

promptly.

• 

Wait until heater is cool before covering.

 NOTE

Summary of Contents for 554HPSQRBLK



















Reviews: