background image

To check the position of the seat and foot rest use these guidelines:

SEAT HEIGHT: Your child's elbows should be at the same height as where the tray 
attaches. 

FOOT REST POSITION: Your child's feet should rest comfortably flat on the foot rest 
so his/her lower legs are straight.

The Connecting Rods are a little bit shorter than the distance between the left 
and right sides to ensure the parts clamp together properly. PLEASE TIGHTEN
THE BOLTS EQUALLY ON BOTH SIDES.

4

    Put the chair into its upright position on a flat, 
    level floor. 

    Level the chair, and then securely tighten ALL 
    of the bolts! 

    

IMPORTANT: DO NOT DISCARD THE ALLEN.

    WRENCH. You MUST regularly check the bolts 
    and retighten as needed using the ALLEN 
    WRENCH included with the chair! Check and  
    retighten 1-2 weeks after initial assembly. 
    Thereafter, check on at least a monthly basis.

    As your child grows you can loosen the bolts 
    to remove the  tray and change the position of 
    the seat and foot rest platforms. 

    Be sure to level the chair and then retighten the 
    bolts securely whenever adjustments are made.

    Put Seat Cushion and Plastic Tray onto the chair. 

I

L

Summary of Contents for EMBASSY 00933










Reviews: