background image

Keypad/Display Menu Navigation

The Series 3100 flow monitor has a two line by 16-character display with two modes of operation and 5 keys on the front 

panel for programming . Two of the keys (Menu and Enter) serve a single function while the three remaining keys (



serve dual purposes .
When the flow monitor is first powered up, it performs internal testing while displaying “Badger Meter DIC Initializing .” At the 

end of the internal testing cycle, the main display appears .
In the normal mode, using the factory defaults, the flow rate displays on the top line and the flow total displays on the 

bottom . Both lines can be custom defined in the field . In the normal mode, ENTER has no function .

Flow Channel 1 Flow Rate and Flow Total

1

      

123.00 GPM 

  

1

 

123456.7 gal

 

Flow Channel 1 Flow Rate and Flow Total

Flow Channel 1 Flow Rate and Flow Channel 2 Rate

1

      

123.00 GPM 

  

 

2

 

123456.70 GPM

 

Flow Channel 1 Flow Rate and Flow Channel 2 Rate

      Channel 2: Pressure and Channel 1: Level

2

      

10.01 PSI 

  

 

1

      

23.09 Feet

 

Channel 2: Pressure and Channel 1: Level

Main Set-up screen accessed by pressing the “MENU” Button

One each screen there are three Choices 

(In this case RESET SETUP and DIAG)

▲ selects RESET   ▼ selects SETUP  and  ► selects DIAG

 

RESET SETUP DIAG 

Main 

Setup

 screen accessed by pressing MENU

.

On each screen there are three options: 

selects 

RESET

 

 selects 

SETUP

 and 

 selects 

DIAG

As seen in the previous figure, on every screen there are Three 

Choices, and three corresponding buttons.  However, on this menu 

“Set-up” there are more choices than fit on the screen. The is 

indicated by the “ 

”. To access these remaining choices press the 

“Enter” Button.

SETUP 

               

    

    

PWORD DSPY FLOW1 

On every screen there are three choices and three 

corresponding buttons . However, on this 

Setup

 menu there 

are more options than fit on the screen . The arrow (

indicates additional options . To access these remaining 

options, press ENTER .

Pressing the “Enter” button again brings up the next set of choices, 

and so on.

Pressing “MENU” button  exits section, back to the previous 

screen, or in some cases back to the Main display screen.

SETUP 

               

    

    

FLOW1 RLY1 RLY2 

Press ENTER again to bring up the next set of choices .

Press MENU to exit an option, or return to the previous 

screen, or—in some cases—to return to the main 

display screen .

Installation

Page 13 

October 2017

CTL-UM-01026-EN-05

Summary of Contents for Data Industrial 3100 Series

































Reviews: