background image

Operating Manual BaehrTec S1200 

 

English – V100 – Status 09/2015

 

Page 3/48 

 

Users notice 

This operating manual must be read through thoroughly before using the device for 
the first time and the contained instructions and rules must be precisely observed. 
 
These operating instructions form part of the device user agreement. By thoroughly 
reading them, you will be familiarised fully with the functioning and operation of the 
device and will therefore be able to recognise and avoid operating errors, dangers 
and damage. 
 
Please retain these operating instructions in a safe place with the device. 
 

 

Please read these operating instructions carefully. 

 

Please keep these operating instructions for reference purposes –  also in case you 
wish to clean the device. 

 

Please observe all warnings and instructions in these operating instructions and on the 
device. 

 

If you ever clean the device, the power supply must be disconnected fully. Remove the 
power plug from the safety outlet. Please observe the information described in 
Chapter 5 and its sub-chapters when cleaning / disinfecting the device. 

 

Do not place the device near heat sources, such as radiators, air-conditioning units, 
refrigerators and the like. Please also avoid positioning near to water sources (for 
example sinks) and / or chemicals.  Ensure an appropriately hygienic environment. 
Place the device on a firm and non-slip  base. Avoid positioning on unstable tables, 
carts or the like. If the device falls, this can cause severe damage and injuries. 

 

To guarantee that the device functions reliably, protect it from cold, and also from 
overheating. Therefore, avoid temperatures below +10° C and above +30° C. 

 

Should you use an extension cable, ensure that the overall power supply is not higher 
than the capacity of the extension cable. Please understand that we cannot accept 
any liability for accessories of any kind not included in the scope of delivery. This also 
applies to any consequential damages that may occur. 

 

Please avoid: 

 

 

Touching plug contacts with sharp and / or metallic objects. 

 

Placing water, beverages and other liquids close to the device. 

 

Leaving children unsupervised with the device. 

 

Touching the mains plug with wet and / or damp hands. 

 

 

Please do not carry out any repairs on the device yourself, as this will result in the 
cancellation of the guarantee claim. For all repairs, please contact qualified experts 
who are authorised to carry these out. If necessary, please ask the manufacturer or 
the distributor of the device (see label on the device). 

 

On the basis of the risk assessment already implemented we have noticed that 
(electro) magnetic fields can lead to interference. Therefore, when using the device, 
please switch off all devices and equipment (mobile telephones, WLAN, etc,) 
completely that generate or could generate such fields. Should this not be feasible, 
then the distance between the S1200 and these devices must be at least 50 cm in 
order to exclude any malfunction form occurring. Please do not use the device in the 
following cases, and contact the manufacturer: 

Summary of Contents for BaehrTec S1200

















































Reviews:

Related manuals for BaehrTec S1200