•
6
•
4. ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY PACK
WARNING
1.
Do not charge battery pack when temperature is below 0°C (32°F) or above
40°C (104°F).
2.
Do not attempt to use a set-up transformer, an engine generator or DC power
receptacle.
3.
Do not allow anything to cover or clog the charger vents.
4.
Always cover the battery pack terminals with the battery pack cover when the
battery pack: is not used.
5.
Do not short the battery pack.
6.
Do not touch the terminals with any conductive material.
7.
Avoid storing battery pack in a container with other metal objects such as
nails, coins, etc.
8.
Do not expose battery pack to water or rain, A battery pack short can use
large current flow, overheating, possible burns and even a breakdown.
9.
Do not store the machine and battery pack in locations where the temperature
may reach or exceed 50°C (122°F).
10.
Do not incinerate the battery pack even if it is severely damaged or
completely worn out. The battery pack can explode in a fire.
11.
Be careful not drop, shake or strike battery pack.
12.
Do not charge inside a box or container of any kind. The battery pack must
be placed in a well ventilated area during charging.
13.
Do not leave batteries unused for extended period of time. Recharge the
battery every 3~6 months and bring Li-Ion battery to 40~80% charge level
before storage.
14.
Li-Ion batteries are sensitive to high temperature and should be kept in a
cool, dry and out of direct light exposure. Ideal temperature for operation and
storage is below 25°C (77°F).
15.
For extension of the battery lifetime, the lithium-ion battery is designed with
the protection function to stop the output.
In the case of described below, when using this product, even if you are
pulling the switch, the motor may stop.
This is not malfunction but the result of protection function.
•
When the battery power remaining runs out, the motor stops.
•
If the tool is overloaded, the motor may stop.
In this case, release the switch of tool and eliminate causes of
overloading. After that you can use it again.
•
If the battery is overheated under overload work, the battery power may
stop. In this case stop using the battery and let the battery cool. After that
you can use it again.
16.
This product is designed with low voltage protection, which prevents the tool
from over discharging and prolongs battery’s lifespan.
Summary of Contents for BCL32G1
