| 25 |
•
20
Die beiden Zylinderschrauben (3) an der
Maschinenhalsaufnahme (2) lösen.
•
20
Die Bohrmaschine (4) von oben bis zum An-
schlag in die Maschinenhalsaufnahme (2) des
Bohrständers einsetzen.
•
20
Die Zylinderschrauben (3) wieder fest zie-
hen.
•
Beim Entnehmen der Diamant-Bohrmaschine
aus dem Bohrständer in umgekehrter Reihenfol-
ge vorgehen.
6.4 Führungsspiel am Bohrschlitten
einstellen
Der Bohrschlitten muss spielfrei laufen, die Einstel-
lung erfolgt über zwei Innensechskantschrauben.
•
21
Klemmhebel (1) lösen.
•
21
Beide Kontermuttern (2) lösen.
•
21
Beide Innensechskantschrauben (3) nach-
stellen bis das Spiel beseitigt ist.
•
21
Beide Kontermuttern (2) anziehen.
•
21
Drehkreuz (4) in beide Richtungen dre-
hen und prüfen, ob der Bohrschlitten (5) spiel-
frei läuft.
HINWEIS
Das Spiel ist richtig eingestellt, wenn sich der
Bohrschlitten mit montierter Diamant-Nassbohr-
maschine bei gelöstem Klemmhebel durch sein Ei-
gengewicht nicht oder nur sehr langsam nach un-
ten bewegt.
6.5 Diamant-Nassbohrmaschine
einschalten und bohren
•
Vor der Inbetriebnahme der Diamant-Nassbohr-
maschine alle Punkte prüfen, die im Kapitel „Vor
Beginn der Arbeit“ beschrieben sind (siehe Sei-
te 20 ff.).
•
Bohrkrone auswählen und montieren (siehe „Di-
amant-Nassbohrkrone montieren bzw. wech-
seln“ auf Seite 21).
HINWEIS
Ein Gangwechsel bei laufender Maschine kann zu
Beschädigungen der Maschine führen.
Den vollständigen Stillstand der Maschine abwar-
ten.
•
5
Drehzahl entsprechend dem Bohrkronen-
durchmesser (siehe „Technische Daten“ auf Sei-
te 18) an der Getriebeumschaltung einstellen.
WARNUNG
Verletzungsgefahr durch herabfallende Bohrkerne.
Î
Bei Durchbruchbohrungen unbedingt die da-
runter bzw. dahinter liegende Räume kontrol-
lieren und den Gefahrenbereich absperren.
Bohrkern mittels Schalung gegen Herunterfal-
len sichern.
•
14
Diamant-Nassbohrmaschine einschalten
und warten, bis Arbeitsdrehzahl erreicht ist –
grüne LED (1) leuchtet auf.
•
10
Wasserzufuhr (1) etwas öffnen.
•
Wasserabsaugung auf Dauerbetrieb einschal-
ten.
•
14
Durch Drehen des Drehkreuzes im Uhr-
zeigersinn die Diamant-Bohrkrone langsam in
das zu bohrende Material eintauchen – grüne
LED (1)darf nicht erlöschen.
•
Sobald die Diamant-Bohrkrone sichtbar im
Bohrmaterial eingetaucht ist, kann der Vorschub
erhöht werden.
HINWEIS
Die Diamant-Bohrkrone kann durch Überhitzung
stumpf oder zerstört werden.
Der Vorschub darf nur so groß sein, wie die Dia-
mant-Bohrkrone das Material abschleifen kann.
Deshalb keinen zu starken Druck auf die Diamant-
Bohrkrone ausüben (siehe „Umgang mit Diamant-
Nassbohrkronen“ auf Seite 27).
•
14
Ist der Vorschub zu schnell, leuchtet die rote
LED (2) auf. Dann sofort den Vorschub verrin-
gern bis die grüne LED (1) wieder aufleuchtet.
Wird dieses Warnsignal nicht beachtet, d. h. der
Vorschub wird nicht verringert, schaltet die Elek-
tronik bei Überlast die Diamant-Nassbohrma-
schine ab.
Der Bohrvorgang kann dann, wie oben beschrie-
ben, begonnen und fortgesetzt werden.
HINWEIS
Hat die Diamant-Bohrkrone keine ausreichende
Schnittleistung, so schaltet die Diamant-Nassbohr-
maschine ebenfalls ab. Prüfen Sie in diesem Fall,
ob die Diamant- Bohrkrone stumpf geworden ist
(siehe „Umgang mit Diamant- Nassbohrkronen“ auf
Seite 27).
Summary of Contents for BDB 819
