| 23 |
3.2 EU Declaration of conformity
We herewith declare, with sole responsibili-
ty, that this product conforms to the following
standards or normative documents:
EN 60745-1:2009 / A11:2010
EN 60745-2-1:2010
EN 55014-1:2006 + A1:2009 + A2:2011
EN 55014-2:2015
EN 61000-3-2:2014
EN 61000-3-3:2013
in accordance with the provisions of the Directives
2006 / 42 / EC; 2014 / 30 / EU; 2011 / 65 / EU
The head of development is authorised to write the
technical documents.
These are available from:
Maschinenfabrik OTTO BAIER GmbH,
Heckenwiesen 26,
71679 Asperg
Germany
Thomas Schwab
Managing Director
Robert Pichl
Factory Manager
Asperg, 27.10.2017
3.3 Machine parts and controls
(See Figure
1
)
1 Bit holder
2 Gear change knob (gear 1 and gear 2)
3 PRCD personal protection switch PRCD
(only BSM 2868 – 110 volt)
4 Connection cable
5 ON / OFF switch
3.4 Intended use
BAIER high-speed mixers are suitable for stirring
paints, plasters, mortars, adhesives and similar mate-
rials. They may
not
be used to stir food, highly flam-
mable or caustic substances.
4
Before Starting Work
To ensure safe working with the high-speed mixers,
the following points must be observed before each
use:
•
Read through all safety instructions and warnings
in this instruction manual.
•
Wear protective clothing such as hard hat, face
protection or safety goggles, safety gloves and if
necessary an apron.
•
The voltage on the rating plate must be identical
with the mains voltage.
•
Before using the machine, always check the con-
nection cable and plug.
1
/
3
Test the personal protection switch
(BSM 2868 – 110 V)
DANGER
Risk of injury due to electric shock.
Î
The PRCD personal protection switch must
be checked each time before the BSM 2868 –
110 V high-speed mixer is started up (see be-
low). If the PRCD does not trip during the test, or
if it switches off repeatedly when the BSM 2868
– 110 V high-speed mixer is switched on, the
BSM 2868 – 1110 V high-speed mixer together
with the PRCD personal protection switch must
be examined by a qualified electrician.
•
3
If the mains plug is plugged in and the
BSM 2868 – 110 V high-speed mixer is switched
off, press the −ON− button (RESET) (2). The red
indicator light (1) must light up.
•
3
Press the −OFF− button (TEST) (3). The
PRCD must switch off, i.e. the red indicator light
(1) goes out.
•
3
Press the −ON− (RESET) button (2) again.
It must now be possible to switch on the
BSM 2868 – 110 V high-speed mixer.
•
If the PRCD does not trip during the test, or if it
switches off repeatedly when the BSM 2868 –
110 V high-speed mixer is switched on, the
BSM 2868 – 110 V high-speed mixer together
with the PRCD personal protection switch must
be examined by a qualified electrician.
•
Operation of the BSM 2868 – 110 V high
speed mixer with a defective PRCD personal
protection switch is not permitted – risk of
fatal injuries.
Summary of Contents for BSM 2868
Page 3: ...3 2 BSM 2868 110 V 230 V 1 BSM 2868 110 V 230 V 3 BSM 2868 110 V ON RESET OFF TEST...
Page 49: ......
Page 50: ......
Page 51: ......
