| 29 |
3.4 Intended Use
BAIER high-speed mixers are suitable for stirring
paints, plasters, mortars, adhesives and similar
materials. They may
not
be used to stir food, highly
flammable or caustic substances.
4
Before Starting Work
To ensure safe working with the high-speed mixers,
the following points must be observed before each
use:
•
Read through all safety instructions and
warnings in this instruction manual.
•
Wear protective clothing such as hard hat, face
protection or safety goggles, safety gloves and if
necessary an apron.
•
The voltage on the rating plate must be identical
with the mains voltage.
•
Before using the machine, always check the
connection cable and plug.
7
/
13
Test the personal protection switch
(only BSM 2863 – 110 V)
DANGER
Risk of injury due to electric shock.
Î
The PRCD personal protection switch must be
checked each time before the BSM 2863 – 110
V high-speed mixer is started up (see below).
If the PRCD does not trip during the test, or if
it switches off repeatedly when the BSM 2863
– 110 V high-speed mixer is switched on, the
BSM 2863 – 110 V high-speed mixer together
with the PRCD personal protection switch must
be examined by a qualified electrician.
•
13
If the mains plug is plugged in and the
BSM 2863 – 110 V high-speed mixer is switched
off, press the −ON− button (RESET) (2). The red
indicator light (1) must light up.
•
13
Press the −OFF− button (TEST) (3). The
PRCD must switch off, i.e. the red indicator light
(1) goes out.
•
13
Press the −ON− button again (RESET) (2).
It must now be possible to switch on the
BSM 2863 – 110 V high-speed mixer.
•
If the PRCD does not trip during the test, or if
it switches off repeatedly when the BSM 2863
– 110 V high-speed mixer is switched on, the
BSM 2863 – 110 V high-speed mixer together
with the PRCD personal protection switch must
be examined by a qualified electrician.
•
Operation of the BSM 2863 – 110 V high-
speed mixer with a defective PRCD personal
protection switch is not permitted – risk of
fatal injuries.
11
BSM 2842 / BSM 2882
•
Mount the D-shaped handle.
DANGER
Risk of injury due to electric shock.
Î
Disconnect the mains plug before carrying out
any work (e.g. changing the stirrer) on the high-
speed mixer.
DANGER
Risk of poisoning due to toxic gases.
Risk of burns and fire due to flammable gases.
Î
Do not process liquids or materials with
unknown hazard potential.
Î
Observe the instructions for use issued by the
manufacturer of the material to be stirred.
Î
When processing plastics, paints, varnishes
and similar materials, do
not
work near
flammable gases or materials.
•
Place the container with the material to be
stirred in a firm, stable position.
•
Mount the additional handle:
f
2
BSM 287
Additional handle (3)
f
5
BSM 288
Additional handle (6)
f
8
BSM 2863 (110 V / 230 V)
Additional
handle (6)
•
Choose stirrers suitable for the material to be
mixed.
•
Mount the stirrer, screw the stirrer into the tool
holder (1), and (2) only for BSM 287, until it
stops:
f
1
BSM 287
f
4
BSM 288
f
7
BSM 2863 (110 V / 230 V)
f
10
BSM 2842 / BSM 2882
•
Switch on the machine at the ON / OFF switch
and set the speed or gear; if empirical values
are not available, start with the lowest speed or
the 1st gear.
Setting the speed:
f
1
/
6
BSM 287
The speed can be continuously adjusted
using the adjusting handwheel (4) on the
handle (5); the handwheel locks in position
at maximum speed.
Summary of Contents for BSM 287
Page 3: ...3 1 BSM 287 2 3...
Page 5: ...5 8 9 7 BSM 2863 110 V 230 V...
Page 6: ...6 10 BSM 2842 BSM 2882 11...
