background image

 

 

20.  Inspect power and control cables periodically. Replace if damaged or bare wires are 

exposed. Bare wiring can kill! 

21.  Maintain machine in top condition. Keep clean for best and safest performance. Follow 

instructions for lubricating and changing accessories. 

22.  Reduce the risk of unintentional starting. Make sure switch is in “OFF” position before 

plugging in power cord. 

23.  Never leave machine running unattended. TURN POWER OFF. Don’t leave machine until it 

comes to a complete stop. 

24.  Make sure machine is disconnected from power supply while motor is being mounted, 

connected or reconnected. 

25. 

Warning:

 The dust generated by certain woods and wood products can be injurious to your 

health. Always operate machinery in well-ventilated areas and provide for proper dust 
removal. Use wood dust collection systems whenever possible. 

 
 
 
 
 
 

TECHNICAL SUPPORT 

 
Our technical support department can be reached at 920.684.4990 and asking for the support 
desk for purchased machines. Tech Support handles questions on machine setup, schematics, 
warranty issues, and individual parts needs: (other than die sets and blades). 
 
For specific application needs or future machine purchases contact the Sales Department at: 
sales@baileigh.com, Phone: 920.684.4990, or Fax: 920.684.3944. 

 

Note: The photos and illustrations used in this manual are representative only and 

may not depict the actual color, labeling or accessories and may be intended to illustrate 
technique only. 

 

 

Note: The specifications and dimensions presented here are subject to change 

without prior notice due to improvements of our products. 

 
 
 
 
 
 

Summary of Contents for DC-1650B

























Reviews: