background image

 

 

21 

21 

Monthly Maintenance 

 

  Apply light machine oil to the rear wheel support to rear wheel handle interface. Two drops of 

oil is sufficient. 

  Check the v-belt tension. If you can hear the belt "slap" the belt guard when the drive motor 

starts, the v-belt requires tensioning. Do this by loosening the four bolts that secure the 
motor to the machine base and slide the motor toward the rear of the machine. Tighten the 
four bolts. 

 
 

Storing Machine for Extended Period of Time 

If this belt grinder is to be inactive for a long period of time, prepare the machine as follows: 

  Detach the plugs from the electrical supply panel. 

  Clean and lubricate the machine. 

  Remove the belt 

  Cover the machine 

 
There are no other maintenance actions required. All bearings are sealed for life and require no 
additional lubrication. 
 
 
 

Idler Wheel Alignment 

 
When idler wheels are removed and/or replaced they must be installed such that they are in 
proper alignment. Failure to properly align the idler wheels will result in premature failure of the 
wheels. 
Premature failure will be evidenced by: 

  Outer diameters being excessively worn such that the wheels lose their factory crown, 

  Wear to a truncated form, or 

  Become out of balance. 

 
The upper and rear idler wheels must operate in the same plane. This means that when they 
are correctly aligned a plane passing through the radial center of the upper wheel will exactly 
pass through the radial center of the rear wheel. 
 
Never perform maintenance or adjustments without first disconnecting the machine from its 
power source. Failure to observe this warning may lead to serious personal injury. 
 

Summary of Contents for BG-260-3-110

































Reviews: