Page
59
Section 19
Maintenance & Inspection
Dragonfly 912
AILERON SUPPORT TUBES & MOUNTING
STEP
INSTRUCTIONS
for Assembly, for Disassembly reverse the order!
PART NO.
STAGE CERT.
1
Bolt AN4-30A, 1/4” washer,
strut plate A,
wing spar leading edge,
strut plate B,
1/4” washer, AN4 full nut.
Very tight.
DFL 004
DFL 005
2
Bolt AN4-30A, 1/4” washer, wing comp strut saddle channel brkt, wing comp
strut, wing comp strut saddle channel brkt, fabric wing sail,
saddle 1” aileron angle,
aileron supp tube,
saddle angle aluminium, (inboard aileron support tube gets wing to main
boom cable after saddle angle aluminium), AN4 half nut.
Loose.
DFP 021
DFC 021
3
Bolt AN3-21A, saddle angle aluminium, aileron supp tube, fabric wing sail,
wing comp strut, 3/16” washer, AN3 half nut.
Loose.
4
Bolt AN3-21A, 3/16” washer, wing comp strut, fabric wing sail, aileron supp
tube, saddle angle aluminium,
threaded insert 1/2” x 10/32 TPI
(hole in insert should be parallel with wing comp strut).
Very tight.
Tighten
bolts
#
2 &
#
3
DFO 040
5
Bolt AN4-5A, cable
wing – tail upper,
wing – tail lower,
wing comp strut saddle channel brkt, 1/4” washer, AN4 half nut.
Very tight.
DFQ 004
DFQ 001
6
Bolt AN4-27A, hinge point,
spacer aileron hinge 1.125”,
aileron supp tube, 1/4” washer, AN4 half nut.
Very tight.
Setting Aileron Angle: Using “Smart Level”. Set ailerons at 16.5 degrees down
compared to Root Tube. Set Level to Zero on Root Tube. Measure angle of Aileron
at inboard part of outer frame, where it is not affected by fabric angles. Adjust using
Ball Joint Rod Ends on Aileron Linkages, both top and bottom,( this occasionally
requires shortening the treads on Ball End Joints by as much as ¼”), and tighten
jamb nuts. (Note: Be sure to hold stick centred during this process.)
DFG 002
(1)
Recommended Special Tools:
Smart Level (digital level)
(2)
The parts needed to perform the task:
Replace worn/damaged parts as needed, listed above. Max. Wear (defined 1.1.8.1)
(3)
Type of maintenance:
Inspection=Line & Replacement=Heavy
(when it involves replacement of structural components.)
(4)
Certification needed to accomplish the task:
Line=LSRI Inspection or above, Heavy=LSRM Maintenance or above.
see:
3 Level of Certification in this manual
(5)
Detailed instructions and diagrams as needed to perform the task, listed above and adjacent page.
Every Annual or 100 Hrs., Inspect for Cracks, Corrosion, Elongation of holes & Fasteners for Wear & Security.
See: 1.3.5 Fabric Coverings: For more inspection and testing information on fabric coverings.
See
Cables, Thimbles and Tangs Page 16
(6)
Method to test/inspect to verify the task was accomplished properly.
Insure that all procedures were followed correctly
and there is proper non-binding movement to moving parts and that fasteners were tightened as instructed. When flight
controls are involved, assure that they are operating properly.
Section 19 Aileron Support Tubes & Mounting
Section 19
Summary of Contents for 912 Dragonfly
