background image

 

4

 

INTRODUCTION 

 

 

Thank you for your purchase of the Balanced Audio Technology VK-40 preamplifier.  

Please read this owner's manual to obtain the full benefit of the VK-40 in your system.  It will 
provide you with the needed safety information and operating procedures for this exceptional 
unit.  
 

 
 

 

WARNINGS:

 

 

To prevent the possibility of serious injury, electrical shock or fire: 

 

DO NOT operate with the cover removed. 

 

DO NOT expose to rain or moisture. 

 

DO NOT defeat the ground power-plug. 

 

DO NOT replace fuse with anything other than the same type and rating as supplied by the factory. 

 

 
 

Package Contents

 

 
 

Included in the box should be the following: 

 

 

 

Description   

 

 

 

Quantity 

 
 

VK-40 Preamplifier   

 

 

 

Power Cord 

 

 

 

 

 

Spare Fuse 

 

 

 

 

  

Torx Wrench (T-10)   

 

 

  

Spare Top Cover Screws 

 

 

  

User’s Manual  

 

 

 

  

VK-R3 Remote Control 

 

 

(If ordered) 

 

 

Save all the packaging material in a safe dry area for the unlikely event that you need to 

return the VK-40 to the factory for service. 
 

Summary of Contents for VK-40



















Reviews: