53857_02-97_A
DIP Switches Definitions
WARNING:
•
Setting DIP switches incorrectly may cause abnormal system behavior and/or damage to system components.
•
Refer to Switchbank illustration on Wiring Configuration page for correct settings for this system.
•
Contact Balboa if you require additional configuration pages added to this hot sheet.
DIP Switchbank A Key
A1
. . . . . . . . . . . . Test Mode (normally Off)
A2 and A3. . . . . . . . . . Control amp draw requirements. See
Table 1
A4*
. . . . . . . . . . . . In “ON” position, displays time in 24 hours (military\European time)
. . . . . . . . . . . . In “OFF” position, displays 12 hour time
A5*
. . . . . . . . . . . . In “ON” position, displays temperature in Celsius
. . . . . . . . . . . . In “OFF” position, displays temperature in Fahrenheit
* Sets default for user preferences - only applies when persistent memory is reset (A12 On)
during power-up
A6
. . . . . . . . . . . . In “ON” position, Equipment timeout 30 minutes (4 hours for Pump 1 Low)
. . . . . . . . . . . . In “OFF” position, Equipment timeout 15 minutes (2 hours for Pump 1 Low)
A7
. . . . . . . . . . . . In “ON” position, Cleanup Cycle – 30 minutes after spa use/timeout, Pump 1 Low & Ozone run for 1 hour
. . . . . . . . . . . . In “OFF” position, NO Cleanup Cycle
A8
. . . . . . . . . . .
In “ON” position, Ozone suppressed for 1 hour after pump or blower button press
. . . . . . . . . . . In “OFF” position, NO Ozone suppression
A9 and A10. . . . . . . . . Circ Pump Behavior settings. See
Table 2
A11
. . . . . . . . . . . . In “ON” position
(non-circ mode operation)
Pump 1 is two-speed, Ozone is ON
in Filter & Cleanup Cycles only
(in any circ mode)
, Pump 1 is one-speed,
Ozone is ON with Circ Pump
. . . . . . . . . . . . In “OFF” position
(non-circ mode operation)
Pump 1 is two-speed, Ozone is
ON with Pump 1 Low
(in any circ mode)
Pump 1 is two-speed, Ozone is ON with Circ Pump
A12
. . . . . . . . . . . . Persistent Memory Reset (used when the spa is powering up)
DIP Switchbank B Key
B1
. . . . . . . . . . . In “ON” position, single-speed Pump 2
. . . . . . . . . . . In “OFF” position, two-speed Pump 2
B2 and B3. . . . . . . . . . Blower Speeds. See
Table 3
B4 and B8
. . . . . . . . . Fiber Optic and Color wheel control; Spa Light Enable
Note: The Light button on an ML900 panel is a SpaLight button.
The Light button on most other panels is an EitherLight button.
B5
. . . . . . . . . . . . Pump 4 enable when On. Jets 4 replaces Blower on Aux panel
B6
. . . . . . . . . . . In “ON” position, Alternate Panel layout
(ML900 scrunching enabled; ML550 and ML700
Jets 3 replaces Blower)
. . . . . . . . . . . In “OFF” position, Normal Panel layout
B7
. . . . . . . . . . . In “ON” position, Spa Light operation is On/Off
. . . . . . . . . . . In “OFF” position, Spa Light operation is dimmable
B9
. . . . . . . . . . . In “ON” position, single-speed Pump 3
. . . . . . . . . . . In “OFF” position, two-speed Pump 3
B10
. . . . . . . . . . . In “ON” position, Pump 3 enabled (Jets 3 replaces
Light button on Aux panel)
. . . . . . . . . . . In “OFF” position, Pump 3 disabled
B11
. . . . . . . . . . . In “ON” position, Mister enabled
. . . . . . . . . . . In “OFF” position, Mister disabled
B12
. . . . . . . . . . . In “ON” position, Mister or Option replaces Blower button on Aux panels
. . . . . . . . . . . In “OFF” position, no button replacement on Aux panels
Table 1
# of Hi-Speed
Pumps/Blower
Before Heat Disabled
A2
A3
OFF
OFF
0
ON
OFF
1
OFF
ON
2
ON
ON
Up to 4
Table 2
Circ Pump
A9
A10
Behavior
OFF
OFF
No Circ Pump
ON
OFF
24 Hr
OFF
ON
24 Hr w/3°F Shut-Off
ON
ON
Acts like Pump 1 Low
(Filter Cycles, Polls)
Table 3
B2
B3
Blower Speeds
OFF
OFF
0 (No Blower)
ON
OFF
1 (on/off)
OFF
ON
2
ON
ON
3
B4 OFF
B4 ON
B8 OFF
B8 ON
No separately-controlled fiber light; spa light enabled on both
SpaLight and EitherLight buttons; fiber light (not wheel) comes on
with spa light (at any intensity)
No separately-controlled spa
light; fiber light enabled on
both FiberLight and EitherLight
buttons; spa light comes on with
fiber light
Spa light and fiber light each
separately controlled; fiber light
enabled on both FiberLight and
EitherLight buttons; spa light
enabled on SpaLight buttons only
