background image

53857_02-97_A

Output Features    

Quadrant

J1  +  W1  

– 2-Speed Pump 1 

3-B

J2  +  W6   – Output tied to Pump 1 Low (J39 - P1-Lo) 

4-B

 

 

 

– OR output tied to Circ Pump (J39 - Circ)

J3  +  W7   – Circ Pump 

5-B

J4  +  W13   – Ozone (Separate Relay 120V or 240V) 

7-B

J5 + W8 

  – 

A.V. 

6-B

J6  +  W12   – 3-speed blower 

8-B

J10 +  W9 

  – 

Spa Light (12V or 120V/240V) (Check J37 setting)  8-C

J7  +  W2   – Misc (120V or 240V) (Check J47 setting) 

2-C

J8  +  W5   – Fiber Optic (12V or 120V/240V) 

4-C

 

 

 

   (Check J47 + J49 setting)

J9  +  W4   – Mister (12V or 120V/240V) (Check J29 setting)  5-C
J11  +  W14   – 2-Speed Pump 2 

5-D

J12  +  W10   – 2-Speed Pump 3 (W30 to J94) 

7-D

 

 

W3 

– Sets Transformer Voltage (120V or 240V) 

4-E

 

 

 

   (Setting must match transformer installed in system.)

X-P632

Used for an additional 2-speed Pump output. 
Relay control J2 plugs into the EXP I/O connector J36 on 
the Main PCBA (Quadrant 7-E, near W10).

Expander boards that REPLACE the Blower function:

Relay control for these options is connected to J21 on the
Main PCBA (Quadrant 9-C, near W9). Do not use the
Blower Connector J6 if one of these is used.

X-P

PN 

5

3

5

44 

Used for an on-off Device without a fuse

X-B

PN 

5

3310 

Used for an on-off Device with 10A fuse

X-P231

PN 

5

3681 

Used for an on-off Device with 30A fuse

PN 

5

3680

Document PN 40593_E

09-20-2006

Pump 5

P

ump 2

To

 J

1

1

PS-2

5

Used to split the output from the Pump 2 Connector (J11)
into a single-speed Pump 2 and single-speed Pump 5.
White wire quick connect goes to Main PCB Red AC for
240 Pumps or to Wht AC for 120V Pumps.

 PN 2

5

094

White

Red

White

Green
Black

Green

White

Red

White

Green
Black

Green

Pump 4

P

ump 3

T

o

 J12

PS-34

Used to split the output from the Pump 3 Connector (J12)
into a single-speed Pump 3 and single-speed Pump 4.
White wire quick connect goes to Main PCB Red AC for
240 Pumps or to Wht AC for 120V Pumps.

 PN 2

5

093

Red

Black

White

Green

Sequencer

SS Pump

SS Pump

ELS-VALVE  

Used to split the output from a single-speed Pump to allow
a Valve Sequencer to be powered by the pump’s output.

 PN 22934

G

R

B

W

J1

W1

J2

J6

F30A 480V

X-P632
PN 53680

P/N 22909 REV B

Expander Options

Summary of Contents for EL Series











Reviews: