background image

Page 7

56016-01_97_A

G

R

B

W

W

W

FUSE 20A 250V

FUSE 3A 250V

K8

K5

J46

F1

J29

J47

J20

J1A

J10

J1

W2

W3

Circ.Pump

12V 

Light

Use this slot for the leftover Red conductor

Line - Black conductor

Balboa Ozone connector configuration for 120V 60Hz 

Ground (Green) conductor

Flat sides of sockets as shown

Common - Install the White conductor here for 120V ozone

Use this slot for the leftover White conductor

Line - Black conductor

Balboa Ozone connector configuration for 240V 60Hz 

Ground (Green) conductor

Common - Install the Red conductor here for 240V ozone

B

G

B

G

Use this slot for the leftover conductor

Line - Black conductor

Ground (Green) conductor

Common - Red for 240V or White for 120V ozone (See W2 wire)

W2 wire determines voltage

Ozone Connections

Ozone Connector Voltage:

 The VS500Z circuit board is factory configured to deliver a preset voltage (120V or 

240V) to the on-board ozone connector (J29). See the ratings table on the wiring diagram attached to the cover 
of the enclosure for the configured voltage.  For 240V output W2 connects to Red AC and for 120V output W2 
connects to White AC.

The voltage to the ozone connector can be changed in the field if required. W2 just needs to be set for the 
required voltage.

WARNING: Changing the voltage of the ozone connector also effects the voltage supplied to the circ 
pump connector (J47). Any equipment controlled by that connector may be damaged if the wrong voltage 
is selected.

Balboa Ozone Generator:

 If the board is set up to operate a 120V ozone generator, the connector on the ozone 

generator is likely to be configured correctly, but should be compared to the illustration below.

If a 240V ozone generator is required, be sure the red wire in the ozone cord is positioned in the connector next 
to the green ground wire as described below.

Note: A special tool is required to remove the pins from the connector body once they are snapped in place. 
Check with your Balboa Account Manager for information on purchasing a pin-removal tool.

Summary of Contents for VS520DZ









Reviews: