background image

www.baldormotion.com

General Information 1-1

MN1940

LT0227A02 Copyright Baldor (c) 2007. All rights reserved.

This manual is copyrighted and all rights are reserved. This document or attached software may not,
in whole or in part, be copied or reproduced in any form without the prior written consent of BALDOR.
BALDOR makes no representations or warranties with respect to the contents hereof and specifically
disclaims any implied warranties of fitness for any particular purpose. The information in this
document is subject to change without notice.
BALDOR assumes no responsibility for any errors that may appear in this document.

Mint

t

is a registered trademark of Baldor.

Windows 95, Windows 98, Windows ME, Windows NT, Windows 2000 and Windows XP are
registered trademarks of the Microsoft Corporation.

Limited Warranty:
For a period of two (2) years from the date of original purchase, BALDOR will repair or replace without
charge controls and accessories which our examination proves to be defective in material or
workmanship. This warranty is valid if the unit has not been tampered with by unauthorized persons,
misused, abused, or improperly installed and has been used in accordance with the instructions and/or
ratings supplied. This warranty is in lieu of any other warranty or guarantee expressed or implied.
BALDOR shall not be held responsible for any expense (including installation and removal),
inconvenience, or consequential damage, including injury to any person or property caused by items of
our manufacture or sale. (Some countries and U.S. states do not allow exclusion or limitation of
incidental or consequential damages, so the above exclusion may not apply.) In any event,
BALDOR’s total liability, under all circumstances, shall not exceed the full purchase price of the
control. Claims for purchase price refunds, repairs, or replacements must be referred to BALDOR with
all pertinent data as to the defect, the date purchased, the task performed by the control, and the
problem encountered. No liability is assumed for expendable items such as fuses. Goods may be
returned only with written notification including a BALDOR Return Authorization Number and any
return shipments must be prepaid.

Baldor UK Ltd
Mint Motion Centre

6 Bristol Distribution Park
Hawkley Drive

Bristol, BS32 0BF
Telephone:

+44 (0) 1454 850000

Fax:

+44 (0) 1454 850001

Email:

technical.support@baldor.co.uk

Web site:

www.baldor.co.uk

Baldor ASR GmbH
Telephone:

+49 (0) 89 90508-0

Fax:

+49 (0) 89 90508-491

Baldor ASR AG
Telephone:

+41 (0) 52 647 4700

Fax:

+41 (0) 52 659 2394

Email:

technical.support@baldor.ch

Australian Baldor Pty Ltd

Baldor Electric Company

Telephone:

+1 479 646 4711

Fax:

+1 479 648 5792

Email:

sales@baldor.com

Web site:

www.baldor.com

Australian Baldor Pty Ltd

Telephone:

+61 2 9674 5455

Fax:

+61 2 9674 2495

Baldor Electric (F.E.) Pte Ltd
Telephone:

+65 744 2572

Fax:

+65 747 1708

Baldor Italia S.R.L
Telephone:

+39 (0) 11 56 24 440

Fax:

+39 (0) 11 56 25 660

1

General Information

1

Summary of Contents for DSM S Series



















































Reviews: