baliv 60 Series, Manual

GB

10

Faucet

Before you begin…

Intended use

The product is at the current level of science and 

technology and meets all valid safety requirements in 

place at the point of introduction, assuming proper 

use.
This faucet is designed for sanitary use only.
The product is not designed for commercial use.
Any other type of use is inappropriate. Improper use 

or modifications to the product or the use of compo-

nents that are not tested and approved by the manu-

facturer may result in unforeseen damage!
Any unintended use or any activities on the product 

not described in these operating instructions are an 

unauthorized misuse outside the manufacturer’s 

legal liability limits.

For your safety

General safety information

•

The user of the product must have read and 

understood these operating instructions prior to 

its first use to ensure the safe handling of this 

product.

•

Please comply with all safety instructions!

•

Store all operating information and safety instruc-

tions for future reference.

•

If you sell or pass on the product, you must also 

pass on these operating instructions.

•

The product may only be used when it functions 

properly. If the product or part of the product is 

defective, take it out of operation and ensure that 

it is disposed of correctly.

•

Only use the product for its intended purpose.

Product-specific safety information

• Important when using in low pressure sys-

tems:

 Before starting up the low pressure or elec-

trical storage heater open the hot water faucet of 

the faucet unit until the water flows without bub-

bles.

•

Faucet for use in private households! Only suita-

ble for use in rooms with a temperature above 0° 

C. In the event of a risk of frost, interrupt the water 

supply and empty the faucet.

•

Be careful when setting the hot water: Risk of 

scalding!

•

If the faucet is not used for a longer period of time, 

first run a large amount of water through it before 

taking water for drinking.

•

Symbols affixed to your product may not be 

removed or covered. Information on the product 

that is no longer legible must be replaced immedi-

ately.

Installation

– After installation, unscrew the mixer jet, rinse the 

pipe and the faucet well (hot/cold water supply) in 

order to rinse out contaminations (shavings and 

hemp residues). Screw the mixer jet back onto the 

outlet after rinsing the faucet.

– Leaks or water outs may cause considerable 

damages to the building or to the contents of your 

home. Check all connections carefully to ensure 

that they are sealed.

Replacing the cartridge

The cartridge is a consumable that may, in the event 

of very hard or dirty water, need to be replaced every 

1 to 2 years.

Cleaning

Sanitary faucets require special care. For this reason, 

please observe the following notes:

•

Chrome-plate surfaces are sensitive to limescale 

removal products, acidic cleaning agents and all 

types scouring agents.

Note: 

A low pressure faucet drips when 

heating water since it functions like a pres-

sure control valve.

Before putting the unit into operation, read 

and observe the operating instructions.

Read and observe the notes regarding 

cleaning agents

Faucet for use in showers

Hot water connection

Cold water connection

Note: 

The images show examples, the fit-

tings may differ from those depicted in terms 

of appearance and scope of delivery. Pay 

attention to the article number on the pack-

aging!

CAUTION! Risk of water damage! 

Instal-

lation must be carried out by an installation 

engineer or by a technically-versed end user 

instructed by an installation engineer.
Failure to observe this requirement shall 

void the warranty.
Prior to the installation and disassembly of a 

faucet, the general water supply should be 

switched off.
When installing the new faucet ensure that 

the seals are positioned correctly. After 

installation, check all connections to ensure 

that they are sealed and test the faucet for 

functionality.
Pipes and fittings must be installed, 

inspected and flushed in accordance with 

current standards and regulations.

NOTICE! Risk of damage to the product! 

Only hand tighten the connection hoses. If 

tightened excessively, the threaded section 

may break off.

NOTICE! Risk of damage to the product! 

Do not metallic cleaning products. Do not 

use aggressive cleaning agents or solvents.