baliv KI-1830, Manual

GB

11

Faucet

Before you begin…

Intended use

The product is at the current level of science and 
technology and meets all valid safety requirements in 
place at the point of introduction, assuming proper 
use.
This faucet is designed for sanitary use only.
The product is not designed for commercial use.
Any other type of use is inappropriate. Improper use 
or modifications to the product or the use of compo-
nents that are not tested and approved by the manu-
facturer may result in unforeseen damage!
Any unintended use or any activities on the product 
not described in these operating instructions are an 
unauthorized misuse outside the manufacturer’s 
legal liability limits.

For your safety

General safety information

•

The user of the product must have read and 
understood these operating instructions prior to 
its first use to ensure the safe handling of this 
product.

•

Please comply with all safety instructions!

•

Store all operating information and safety instruc-
tions for future reference.

•

If you sell or pass on the product, you must also 
pass on these operating instructions.

•

The product may only be used when it functions 
properly. If the product or part of the product is 
defective, take it out of operation and ensure that 
it is disposed of correctly.

•

Only use the product for its intended purpose.

Product-specific safety information

• Important when using in low pressure sys-

tems:

 Before starting up the low pressure or 

electrical storage heater open the hot water fau-
cet of the faucet unit until the water flows without 
bubbles.

•

Faucet for use in private households! Only suita-
ble for use in rooms with a temperature above 0° 
C. In the event of a risk of frost, interrupt the 
water supply and empty the faucet.

•

Be careful when setting the hot water: Risk of 
scalding!

•

If the faucet is not used for a longer period of 
time, first run a large amount of water through it 
before taking water for drinking.

•

Symbols affixed to your product may not be 
removed or covered. Information on the product 
that is no longer legible must be replaced imme-
diately.

Installation

– After installation, unscrew the mixer jet, rinse the 

pipe and the faucet well (hot/cold water supply) in 
order to rinse out contaminations (shavings and 
hemp residues). Screw the mixer jet back onto 
the outlet after rinsing the faucet.

– Leaks or water outs may cause considerable 

damages to the building or to the contents of your 
home. Check all connections carefully to ensure 
that they are sealed.

Replacing the cartridge

The cartridge is a consumable that may, in the event 
of very hard or dirty water, need to be replaced every 
1 to 2 years.

Note: 

A low pressure faucet drips when 

heating water since it functions like a pres-
sure control valve.

Before putting the unit into operation, read 
and observe the operating instructions.

Read and observe the notes regarding 
cleaning agents

Faucet for use in kitchens

Hot water connection

Cold water connection

Observe the more detailed information on 
the next pages

Optional fixture sets. Check the scope of 
delivery prior to installation. Depending on 
the faucet, there are fixture sets included in 
the scope of delivery which may differ from 
the one depicted.

Information regarding the fixture of water 
pipes

Note: 

The images show examples, the fit-

tings may differ from those depicted in terms 
of appearance and scope of delivery. Pay 
attention to the article number on the pack-
aging!

CAUTION! Risk of water damage! 

Instal-

lation must be carried out by an installation 
engineer or by a technically-versed end 
user instructed by an installation engineer.
Failure to observe this requirement shall 
void the warranty.
Prior to the installation and disassembly of a 
faucet, the general water supply should be 
switched off.
When installing the new faucet ensure that 
the seals are positioned correctly. After 
installation, check all connections to ensure 
that they are sealed and test the faucet for 
functionality.
Pipes and fittings must be installed, 
inspected and flushed in accordance with 
current standards and regulations.

NOTICE! Risk of damage to the product! 

Only hand tighten the connection hoses. If 
tightened excessively, the threaded section 
may break off.