background image

11 

 

Clean the glass only when the stove is cold, using cotton cloth or paper towels and glass 

cleaner. 

-

 

Make sure the ashtray is placed correctly and that the door is fully closed. 

-

 

With the vacuum cleaner, remove the ash from the ash niche only when it has completely 

cooled down. 

-

 

Do not use abrasive cleaners for the surface of the stove. 

 

 

7.3. Turning on the stove for the first time 

-

 

Make sure all cables are connected correctly. 

-

 

Turn on the stove. 

You have bought a quality appliance. Enjoy your home while creating good thermal comfort and 

coziness. 

 

8.

 

Warranty Terms 
 

The duration of the warranty is 24 months from the date of sale. The warranty is considered void 

under the following conditions: 

 

Incorrect connection; 

 

Repair and/or modification attempts by the customer; 

 

Visible damage to the exterior and/or interior of the product; 

 

Damage caused by lightning storms and/or electric shocks; 

 

Use in unacceptable conditions / temperature and humidity /; 

The removal of factory defects during the warranty period does not lead to its extension. In case 

of malfunction, the product should be sent to the seller. 

 

9.

 

Cleaning and maintenance of the pellet stove 

 

It is recommended that the burner pot, ashtray and ashtray niche be cleaned after each use, 

every day. 

The burner pot can be cleaned during operation of the pellet stove by a cleaning mechanism that 

is controlled by the controller. 

Using a vacuum cleaner for stoves makes cleaning the pellet stove easier. The vacuum cleaner 

must have a filter to prevent dust from entering the room or the room where it is located. 

Before you start cleaning, the following precautions should be taken: 

 

Unplug the stove from the mains. 

 

Before working, make sure that the stove and ashes are cooled. 

 

The sealing strip on the underside of the burner pot must be in place and must not be damaged 

(Fig. 10). 

 

Chimneys should be cleaned twice a year and before each heating season. The chimney should 

be checked and cleaned every year, preferably at the beginning of the heating season. 

 

Smoke fan – to be checked and cleaned every six months. 

 

Perform general cleaning at the beginning and end of the heating season. 

The purpose of this special maintenance is to ensure proper and efficient operation of the pellet 

stove. 

In the event of a flue or chimney fire, get everyone out 

the room, turn off the power using the main switch and remove the plug from the wall (the plug 

should always be easily accessible), and immediately call the fire brigade.

Summary of Contents for Sofia















Reviews: