background image

REV: 5/2013  

IM-268S-11  2013 © Bally Refrigerated Boxes, Inc.

    

 

 

1

 

 

 

SERVICE MANUAL 

WALK-IN COOLERS AND FREEZER 

IM-268S-11

 

 

 
Routine maintenance  

 2 

 

Safety Walk Strips  

 2 

 

Gaskets 

Replacing magnetic gasket on hinged Walk-In doors  

 3 

Replacing wiper gasket at bottom of hinged Walk-In door  

 3 

 

Hinged Walk-In Doors 

Replacing the D-1000 touch latch on Walk-In doors  

 4 

Replacing D-1250 spring loaded hinges on Walk-In door panels  

 5 

Shimming Walk-In door hinges  

 5 

 
Anti-Condensate Heaters 

Replacing anti-condensate heater element around door frame of hinged Walk-In doors  

 6 

 

Reach-In Doors 

Replacing magnetic gasket on hinged Reach-In doors  

 7 

Adjusting self-closing hinges on Reach-In doors  

 7 

Replacing hinges on Reach-In door panels   

 8 

Replacing anti-condensate heater element around frame of hinged Reach-In doors  

 8 

 
Pressure Relief Port 

Replacing klixon on Pressure Relief Port  

 9 

Replacing anti-condensate heaters on Pressure Relief Ports  

 9 

Replacing magnetic gasket on Pressure Relief Ports  

 9 

 

Door Closer 

Replacing Door Closer 

10 

 
 

 

 

 

Summary of Contents for IM-268S-11











Reviews: