baltur TBG 2000 MC, Installation, Use And Maintenance Instruction Manual

ENGLISH

5 / 30

0006160236_201711

Special instructions for using gas.

•  Check that the feed line and the train comply with current standards 

and regulations.

•  Check that all the gas connections are properly sealed.

•  Do not leave the equipment on when it is not in use and always 

close the gas cock.

•  If the user is away for some time, close the main gas feed valve 

to the burner.

•  If you smell gas:

 - do not operate electrical switches, the phone or any other 

object that can cause sparks;

 - immediately open doors and windows to create a draught to 

clear the air in the room;

 - close the gas cocks;

 - have professionally qualified personnel correct the fault.

•  Do not block ventilation openings in the room where there is gas 

equipment or dangerous situations may arise with the build up of 

toxic and explosive mixtures.

RESIDUAL RISKS

•  In spite of the accurate product planning according to the regulations 

in force, residual risks may still be present during correct use. They 

are indicated on the burner by means of specific Pictograms.

CAUTION

Mechanical parts in motion.

CAUTION

Materials at high temperatures.

CAUTION

Energised electrical switchboard

INSTRUCTIONS ON ELECTRICAL SAFETY

•  Check that the equipment is properly grounded according to the 

safety standards in force.

•  Do not use the gas pipes to ground electrical equipment.

•  If in doubt, call for a careful electrical check by a qualified technician, 

since the manufacturer will not be liable for any damage caused by 

a poor ground connection.

•  A  professional  check  should  be  carried  out  to  ensure  that  the 

electrical installation is adequate for the maximum output absorbed 

by the system. This is indicated on the data plate.

•  Make sure that the system cable cross-section is suitable for the 

power absorbed by the equipment.

•  The  use  of  adaptors,  multiple  plugs  and/or  extension  leads  to 

supply power from the mains to the appliance is not allowed.

•  For  the  connection  to  the  mains,  fit  an  omnipolar  switch  with  a 

contact opening gap equal to or greater than 3 mm in accordance 

with current safety regulations (Overvoltage category III).

•  Use only double insulated cables with external thickness of at least 

1mm for the power supply of the burner.

•  Unsheathe the external insulating cover of the power cable to the 

necessary extent for the connection, thus avoiding the wire from 

coming into contact with metal parts.

•  The electrical supply to the burner must have neutral to ground 

connection. In the case of a ionisation current check with neutral 

not to ground, it is essential to make a connection between terminal 

2 (neutral) and the ground for the RC circuit.

•  If the user is away for some time, close the main gas feed valve 

to the burner.

•  The use of any components that use electricity means that certain 

fundamental rules have to followed, including the following:

 - do not touch the equipment with parts of the body that are wet 

or damp and/or with damp feet

 - do not pull on electrical cables;

 - do not leave the equipment exposed to atmospheric agents 

(such as rain or sun etc.) unless there is express provision for 

this.

 - do not allow the equipment to be used by children or 

inexperienced persons.

 - The power supply cable for the equipment not must be replaced 

by the user. If the cable is damaged, turn off the equipment. To 

replace the cable, contact exclusively qualified personnel.

 - If you decide not to use the equipment for a while it is advisable 

to switch off the electrical power supply to all components in the 

system that use electricity (pumps, burner, etc.).

•  Use flexible cables compliant with standard EN60335-1:

 - if PVC sheathed at least H05VV-F

 - if rubber sheathed at least H05RR-F

 - if unsheathed at least FG7 or FROR