14
Power Drive & Roll-A-Pro
®
installation instructions
13.1 Safety Beams
A Safety Beam Kit may be fitted to this opener. When this option
is fitted, the operation of this device is such that if an object (i.e
car, child etc) blocks the Infra-Red beam, then the garage door
opener will not close the door automatically. If the Safety Beam
is fitted but not operating coreectly, then the door once opened
automatically, will not close automatically.
13.2 Auto Close Option
Auto-Close mode is a function that automatically closes the
door a preset time after the Safety Beams recognise that a
vehicle has left the garage. The Auto-Close timer only starts after
the Safety Beam’s path is broken. If the safety beam path is not
broken, the door will remain open until the path is broken. If the
opener incurs a physical obstruction (i.e. not from the Safety
Beams) while closing the door, it will re-open and not Auto-Close
until the Safety Beam’s path is broken again.
To enable the Auto-Close function remove the light diffuser from
the opener and remove the AUTO-CLS (ACLS) shunt next to the
programmer input and place over both ACLS inputs. When this
option is selected the garage door opener will attempt to close
the door automatically 30 seconds after opening. Refit the light
diffuser.
13. Auto-Close (CAD PD Only)
WARNING! It is compulsory to have
Safety Beams installed when using
Auto-Close mode.
Remove shunt
and place over
both inputs.
14. Coding a Transmitter
14.1 Storing the Transmitter Code
S T E P O N E
The opener can only be operated from remote
controllers that have been programmed into its
memory. Up to 64 remotes (8 for Roll-A-Pro) can be
programmed.
S T E P T H R E E
Switch power on
Press and
release
HOLD for 3 sec
HOLD for 3 sec
RELEASE
S T E P F O U R
Press to test
tip
remove
controls cover
S T E P T W O
RELEASE
C O D I N G R E M O T E F R O M T H E O P E N E R
S T E P O N E
S T E P T W O
Take a pre-coded
remote and press the
button to duplicate
R E M O T E L Y C O D I N G A R E M O T E C O N T R O L
Remotely coding works when you have a
pre-coded remote control and are in range of the
opener.
tip
Use a pen,
HOLD for 2 sec
the middle button
through the
coding hole
S T E P T H R E E
Opener flashes & beeps
HOLD for 3 sec
HOLD for 3 sec
RELEASE
Take new
remote
RELEASE
S T E P F I V E
Press to test
Opener stops flashing &
beeping
14.2 Remotely Coding Transmitters
S T E P O N E
The opener can only be operated from remote
controllers that have been programmed into its
memory. Up to 64 remotes (8 for Roll-A-Pro) can be
programmed.
S T E P T H R E E
Switch power on
Press and
release
HOLD for 3 sec
HOLD for 3 sec
RELEASE
S T E P F O U R
Press to test
tip
remove
controls cover
S T E P T W O
RELEASE
C O D I N G R E M O T E F R O M T H E O P E N E R
S T E P O N E
S T E P T W O
Take a pre-coded
remote and press the
button to duplicate
R E M O T E L Y C O D I N G A R E M O T E C O N T R O L
Remotely coding works when you have a
pre-coded remote control and are in range of the
opener.
tip
Use a pen,
HOLD for 2 sec
the middle button
through the
coding hole
S T E P T H R E E
Opener flashes & beeps
HOLD for 3 sec
HOLD for 3 sec
RELEASE
Take new
remote
RELEASE
S T E P F I V E
Press to test
Opener stops flashing &
beeping
Remote code set is disabled when:
• powered by battery backup
• the service indicator is active
• when the door is indifcating that it as
prevented from closing by a P.E beam
being blocked.
tip
